air - HICLOVER Incinerator

waste

Medical Incineraotors chamber of post combustion

Jun 23, 2021 by hiclover 0 Comments #air, #ashing, #box, #burner, #chamber, #combustion, #control, #de, #device, #English, #gases, #injection, #post, #refractory, #regulation, #thickness

1.A chamber of post combustion of gases
A burner of combustion of gases,
A device of injection of air allowing a total re-combustion of gases,
A device of air inlet of cooling of waste gases,
A sheath of evacuation of the gases burnt,
Carcass in strong sheet steel with support of connection
Composition of the refractory;
Refractory concrete:
Thickness :>150mm
Nature: 65%% of Al203
Insulate in fibrous panels:
Thickness: >85mm
Nature: Calcium
Burner with fuel, mono-bloc casting guiding type with horizontal flame, lighting and safety of electronic ignition, permanent ventilation,
electromagnetic sluice gate of regulation and isolating valve.
A secondary injection of air to ensure perfect oxygen content.
2.A control box ensuring the complete cycle of combustion.
3.Fan:
Electro-ventilator distributing the secondary air, the regulation of the air flow being carried out by valves and following the control of
the automatic cycle.
4.Controls and regulations:
Control box watertight to dust, including:
A switch circuit breaker for each engine (ventilators and burners).
A timer with adjustable temporization for the regulation of each burner.
A regulator with digital watching for the temperature of combustion.
A regulator with digital watching for the temperature of post-combustion.
Electric box.
5.The de-ashing must be done in the bottom of the combustion chamber or the de-ashing should be automatic or manual batch de-ashing.
6.Process filtering system: scrubber to be mentioned as optional
7.Emission standards compliance: BS 3316 or equivalent standard
8.Capacity to treat plastic: not less than 40% by weight
9.CE manufacturing compliance: BS EN 746-2-1997

waste

Medical Incineraotors chamber of post combustion

Jun 23, 2021 by hiclover 0 Comments #air, #ashing, #box, #burner, #chamber, #combustion, #control, #de, #device, #English, #gases, #injection, #post, #refractory, #regulation, #thickness

waste

Controlled air medical waste incinerator designed for incineration of bio-medical waste

Jun 21, 2021 by hiclover 0 Comments #air, #bio, #chamber, #combustion, #controlled, #designed, #diesel, #English, #incineration, #incinerator, #m, #medical, #operational, #specs, #standards, #waste

Controlled air medical waste incinerator designed for incineration of bio-medical waste generated at a blood-processing center. The waste to be treated mainly includes bio-waste (i.e. bodily fluids), infectious and hazardous waste such as syringes, needles, and other medical waste (i.e. silicon rubbers, plastic, textiles, papers, packs, etc.)

Operational Specs Physical Specs
Combustion Chamber Volume (m3) 8.80m3
Burn Rate* up to 1,500kg per hour
Average Fuel Consumption 65 kg per hour or more (7 diesel burners)
Operational Temperature 850 – 1320°C
Gas Retention in Secondary Chamber Large secondary chamber
Temperature Monitoring Yes
Average ash residue (%) 3%
Thermostatic Device Yes
1000l diesel flue tank
Venture gas scrubber
Hydraulic Ram Feeding System
Diesel Powered Large Incinerator
Minimum Specification Required

Standards
1) Bidder or Manufacturer ISO 9001 Certified
2) Respecting international emission standards
Electrical characteristics
3) A 230V, 60Hz single-phase electrical source.
4) Protections against over-voltage and over-current line conditions.
5) Compliance with applicable Ghanaian standards and regulations.
Operational characteristics
6) Two-stage incineration with dual chamber combustion
7) Burn rate: 15 – 20 Kg/h
8) Capacity: not less than 130 L
9) Concentrations of most pollutants in stack gases below detection limits
10) Diesel fuel
11) Electronic system control
12) Easy to operate and minimal training
13) Any accessory or dedicated device necessary to the proper functioning and utilization of the equipment included

PLEASE REFER TO BROCHURES ATTACHED FOR DETAILED SPECIFICATION

waste

Controlled air medical waste incinerator designed for incineration of bio-medical waste

Jun 21, 2021 by hiclover 0 Comments #air, #bio, #chamber, #combustion, #controlled, #designed, #diesel, #English, #incineration, #incinerator, #m, #medical, #operational, #specs, #standards, #waste

PLEASE REFER TO BROCHURES ATTACHED FOR DETAILED SPECIFICATION

waste

Supply, Installation and Commissioning of DIESEL FIRED INCINERATORS

Jun 21, 2021 by hiclover 0 Comments #air, #ash, #automatic, #c, #combustion, #diesel, #door, #English, #fired, #loading, #material, #primary, #provided, #system, #temperature, #type

Supply, Installation and Commissioning of DIESEL FIRED INCINERATORS
Medical Waste Incinerator, 100 to 120 Kg/hr
Application   For incineration, general and pathological
Capacity    100 C 120 kg/h burn rate
Type Two  combustion chambers type; primary  and Secondary, controlled/forced combustion air type with a flue gas emission scrubbing unit
Operating time                Minimum 8 hours daily
Operating temperature     From 850 0C to 1200 0C, Automatic controlled
Residual Ash                    5 to 10%
Construction Constructed from heavy duty mild or aluminized  steel
Or equal and approved equivalent

Insulation material            Refractory material lining similar or equal to calcium
Silicate and hot face combination of heavy duty brickwork
Internal Construction        Fixed hearth type complete with gratings, concave bottom and charging door, lined with refractory material
Charging Door                   Suitable for manual loading of wastes and with smooth
Dear seal equivalent of Ceramic seals with hinges.
Door Lock                          Automatic, Electric type
Ash removal door    Provided, for removing resultant bottom ash leftovers                              from the Primary chamber
Gratings    Provided
Loading Manual loading of waste
Primary Burner                        Fully automatic, with fuel, temperature and speed  controls with ignition system  flame detector                                                         Air fan Complete with safety features, flame failure                                                                    Diesel fired fuel injector type
Flange mounted
Blower   Provided.  3 phase for supplying excess combustion air through the distribution system with speed control system
Temperature Minimum exit 850 0C
Observation port To be provided with protective glass type
     3.3    Secondary chamber

waste

Supply, Installation and Commissioning of DIESEL FIRED INCINERATORS

Jun 20, 2021 by hiclover 0 Comments #air, #ash, #automatic, #c, #combustion, #diesel, #door, #English, #fired, #loading, #material, #primary, #provided, #system, #temperature, #type

waste

MEDICAL WASTE INCINERATOR (50 C 60kg/hr)

Jun 20, 2021 by hiclover 0 Comments #air, #automatic, #c, #combustion, #controlled, #English, #material, #medical, #provided, #shall, #system, #temperature, #type, #unit, #waste

Medical Waste Incinerator, 50 to 60 Kg/hr
Support Health Sector Support Project
Point of Installation (Hospitals) Moi Voi, Makindu, Maragua, Eldama Ravine and Isiolo District Hospitals
1.    General Description
Supply, delivery, installation and commissioning of a medical waste incinerator suitable for disposal of Medical, General and Pathological waste in a safe and clean environment.  The unit shall consist of two chambers and operate on the principal of controlled air and temperature. The unit shall consist a particulate remover (scrubbers) as stipulated in waste management regulations, 2006 (Legal notice NO. 121 of 29th September, 2006).  The Unit shall be fully automatic and controlled by an automatic electronic controlled system except loading system which shall be manual.  The unit shall be capable of incinerating between 50 to 60 kg of solid medical waste per hour.  It shall be constructed from mild or aluminized steel lined with refractory material.
Main unit
Application For incineration, general and pathological
Capacity   50 C 60 kg/h burn rate
Type Two  combustion chambers type; primary  and Secondary, controlled/forced combustion air type with a flue gas emission scrubbing unit
Operating time                Minimum 8 hours daily
Operating temperature     From 850 0C to 1200 0C, Automatic controlled
Residual Ash                    5 to 10%
    3.2     Primary Chamber
Construction Constructed from heavy duty mild or aluminized  steel Or
equal and approved equivalent
Insulation material            Refractory material lining similar or equal to calcium
Silicate and hot face combination of heavy duty brickwork
Internal Construction        Fixed hearth type complete with gratings, concave bottom
and charging door, lined with refractory material
Charging Door                   Suitable for manual loading of wastes and with smooth
Dear seal equivalent of Ceramic seals with hinges.
Door Lock                          Automatic, Electric type
Ash removal door    Provided, for removing resultant bottom ash leftovers                              from the Primary chamber
Gratings   Provided
Loading Manual loading of waste
Primary Burner                        Fully automatic, with fuel, temperature and speed controls with ignition system, flame detector, Air fan complete with safety features, flame failure,  Diesel fired fuel injector type and Flange mounted
Blower Provided. For supplying excess combustion air through the distribution system with speed control system
Temperature Minimum exit 850 0C
Observation port To be provided with protective glass type
Construction   Constructed from heavy duty mild or aluminized steel or equal and approved equivalent
Insulation Refractory material lining
Combustion Temperatures        Above 850 0C, controlled electronically
Gas residue or retention Time       > 2 second at minimum 850 0C
Secondary Burner                    Provided, Diesel fired, fully automatic, with fuel, temperature and speed controls, With ignition system,                                                                  Flame detector, Air fan, Complete with safety features, flame failure Diesel fired fuel injector type.                                                                  Flange mounted
Ejector Provided, Venturi type, for cooling the flue gases
Combustion Air Fan Provided for supplying combustion and creating a negative drift and turbulences
Temperature Maximum  1600 0C

waste

MEDICAL WASTE INCINERATOR (50 C 60kg/hr)

Jun 20, 2021 by hiclover 0 Comments #air, #automatic, #c, #combustion, #controlled, #English, #material, #medical, #provided, #shall, #system, #temperature, #type, #unit, #waste

waste

fabricantes de incineradores de residuos china

Jun 15, 2021 by hiclover 0 Comments #air, #au, #chambre, #combustion, #de, #des, #du, #en, #Español, #est, #et, #la, #les, #pour, #temp, #un

5-1- Chambre de post combustion est installée au dessus du foyer de combustion, elle est constituée d’un

cylindre métallique revêtu intérieurement d’une couche d ‘isolant et d’une couche de matériaux réfractaires.

5-2- ¿Volumen interior ?: 2,1 m3

Est dimensionnée pour pouvoir garantir un temps de fumée de 2 secondes à 1100 ° C avec un pourcentage d’oxygène libre

d’au moins 6%.

5-3 -Accesorios

? Trappe de visite boulonnée frontal pour permettre l’inspection périodique

? La liaison à la chambre de combustion est tapissée de réfractaire

? Instalación de les br? Leurs

? Instalación de sondes de mesure température

PRODUCCIÓN DE L’AIR COMBURANT DE LA CHAMBRE DE POST COMBUSTION

Centrifugadora Ventilateur

? Tuyauteries de distribution d’air

? Série de vannes de distribution d’air

? Soupape de régulation de l’air soufflé asservi par la sonde du débit d ‘oxygène

BRULEUR DE LA CHAMBRE DE POST COMBUSTION

Sont prévus 2 br? Leurs du type à l’air soufflé au gasoil équipés des dispositifs de sécurité.

A la mise en route du cuatro les deux br? Leurs sont allumés pour assurer la température minimale d’au moins 1100 ° C ?;

ils restent en marche sucesivement pour maintenir la température constante.

Puissance thermique installée (290 + 350) KW.

QUIMICA DE EVACUACION

Constitué par un conduit métallique vertical de 8 m de long installée au-dessus de la chambre de PC, diamètre 630 mm

en t? le d’acier au carbone avec garnissage intérieur en réfractaire

REGLAMENTO ARMOIRE ELECTRIQUE DE COMMANDE ET

Composée de ?:

? Circuito 380 V- 50 HZ-3 fases

? Voyant sous tension

? Commande d’arrêt général

? Voyant état des bruleurs

? Affichage des températures des deux chambres

? Minuterie des temps des ciclos.

? Una variación des vitesses des ventilateurs

? Le tableau et les cablages sont prévus aux règles CEI avec protección IP 55

? Microprocesseur pour le contr? Le et la régulation des températures, ainsi que les cycles d’opération

? Cablages réalisés selon les règles CEI.

INSTRUMENTATION DE CONTROLE ET DE MESURAGE CONTINU

Les dispositifs suivants sont prévus ?:

1) ¿Termopares para la mesure de la température en chambre de combustion? et postcombustión, à la sortie de

l’échangeur dans la section d’entrée du filtre

2) Système de mesure de la concentración d’oxygène dans les fumées humides a la sortie de la chambre de postcombustión

constitué de ?:

? Sonde de mesure de l’oxygène à l’oxyde de zirconium

? Pompe à la membrana

débitmètre

El Contratista suministrará un Incinerador en régimen de alquiler en un lugar establecido por la Compañía. La

El contratista debe proporcionar personal capacitado y competente con la instalación inicial, puesta en servicio y operación.

formación bajo la supervisión del técnico del fabricante. El incinerador debe ser mantenido y operado para

especificaciones del fabricante por personal capacitado. El contratista debe tener suficiente personal capacitado y competente para

operar el incinerador durante todo el período del contrato. Las especificaciones del incinerador se adjuntan en el Apéndice A.

waste

Controlled air medical waste incinerator designed for incineration of bio-medical waste

Jun 12, 2021 by hiclover 0 Comments #air, #bio, #burn, #chamber, #controlled, #designed, #diesel, #English, #incineration, #incinerator, #m, #medical, #operational, #rate, #specs, #waste

Standards1) Bidder or Brand ISO 9001 Certified2) Respecting international emission standardsElectrical characteristics3) A 230V, 60Hz single-phase electrical source.4) Protections against over-voltage and over-current line Requirements.5) Compliance with applicable Ghanaian standards and regulations.Operational characteristics6) Two-stage incineration with dual chamber combustion7) Burn rate: 15 – 20 Kg/h8) Ability: not less than 130 L9) Concentrations of most pollutants in stack gases under detection limits10) Diesel fuel11) Electronic Machine control12) Easy to operate and minimal training13) Any accessory or dedicated Apparatus necessary to the proper functioning and utilization of the equipment included

Tag: air