Tag: diesel

Controlled air medical waste incinerator designed for incineration of bio-medical waste

Controlled air medical waste incinerator designed for incineration of bio-medical waste generated at a blood-processing center. The waste to be treated mainly includes bio-waste (i.e. bodily fluids), infectious and hazardous waste such as syringes, needles, and other medical waste (i.e. silicon rubbers, plastic, textiles, papers, packs, etc.)

Operational Specs Physical Specs
Combustion Chamber Volume (m3) 8.80m3
Burn Rate* up to 1,500kg per hour
Average Fuel Consumption 65 kg per hour or more (7 diesel burners)
Operational Temperature 850 – 1320°C
Gas Retention in Secondary Chamber Large secondary chamber    
Temperature Monitoring Yes    
Average ash residue (%) 3%    
Thermostatic Device Yes  
1000l diesel flue tank
Venture gas scrubber
Hydraulic Ram Feeding System
Diesel Powered Large Incinerator
Minimum Specification Required

Standards
1) Bidder or Manufacturer ISO 9001 Certified
2) Respecting international emission standards
Electrical characteristics
3) A 230V, 60Hz single-phase electrical source.
4) Protections against over-voltage and over-current line conditions.
5) Compliance with applicable Ghanaian standards and regulations.
Operational characteristics
6) Two-stage incineration with dual chamber combustion
7) Burn rate: 15 – 20 Kg/h
8) Capacity: not less than 130 L
9) Concentrations of most pollutants in stack gases below detection limits
10) Diesel fuel
11) Electronic system control
12) Easy to operate and minimal training
13) Any accessory or dedicated device necessary to the proper functioning and utilization of the equipment included

PLEASE REFER TO BROCHURES ATTACHED FOR DETAILED SPECIFICATION

Controlled air medical waste incinerator designed for incineration of bio-medical waste

Controlled air medical waste incinerator designed for incineration of bio-medical waste generated at a blood-processing center. The waste to be treated mainly includes bio-waste (i.e. bodily fluids), infectious and hazardous waste such as syringes, needles, and other medical waste (i.e. silicon rubbers, plastic, textiles, papers, packs, etc.)

Operational Specs Physical Specs
Combustion Chamber Volume (m3) 8.80m3
Burn Rate* up to 1,500kg per hour
Average Fuel Consumption 65 kg per hour or more (7 diesel burners)
Operational Temperature 850 – 1320°C
Gas Retention in Secondary Chamber Large secondary chamber    
Temperature Monitoring Yes    
Average ash residue (%) 3%    
Thermostatic Device Yes  
1000l diesel flue tank
Venture gas scrubber
Hydraulic Ram Feeding System
Diesel Powered Large Incinerator
Minimum Specification Required

Standards
1) Bidder or Manufacturer ISO 9001 Certified
2) Respecting international emission standards
Electrical characteristics
3) A 230V, 60Hz single-phase electrical source.
4) Protections against over-voltage and over-current line conditions.
5) Compliance with applicable Ghanaian standards and regulations.
Operational characteristics
6) Two-stage incineration with dual chamber combustion
7) Burn rate: 15 – 20 Kg/h
8) Capacity: not less than 130 L
9) Concentrations of most pollutants in stack gases below detection limits
10) Diesel fuel
11) Electronic system control
12) Easy to operate and minimal training
13) Any accessory or dedicated device necessary to the proper functioning and utilization of the equipment included

PLEASE REFER TO BROCHURES ATTACHED FOR DETAILED SPECIFICATION

Supply, Installation and Commissioning of DIESEL FIRED INCINERATORS

Supply, Installation and Commissioning of DIESEL FIRED INCINERATORS
Medical Waste Incinerator, 100 to 120 Kg/hr
Application   For incineration, general and pathological
Capacity    100 C 120 kg/h burn rate
Type Two  combustion chambers type; primary  and Secondary, controlled/forced combustion air type with a flue gas emission scrubbing unit
Operating time                Minimum 8 hours daily
Operating temperature     From 850 0C to 1200 0C, Automatic controlled
Residual Ash                    5 to 10%
Construction Constructed from heavy duty mild or aluminized  steel
Or equal and approved equivalent

Insulation material            Refractory material lining similar or equal to calcium 
Silicate and hot face combination of heavy duty brickwork
Internal Construction        Fixed hearth type complete with gratings, concave bottom and charging door, lined with refractory material
Charging Door                   Suitable for manual loading of wastes and with smooth 
Dear seal equivalent of Ceramic seals with hinges.
Door Lock                          Automatic, Electric type
Ash removal door    Provided, for removing resultant bottom ash leftovers                              from the Primary chamber
Gratings    Provided
Loading Manual loading of waste
Primary Burner                        Fully automatic, with fuel, temperature and speed  controls with ignition system  flame detector                                                         Air fan Complete with safety features, flame failure                                                                    Diesel fired fuel injector type                                               
Flange mounted
Blower   Provided.  3 phase for supplying excess combustion air through the distribution system with speed control system
Temperature Minimum exit 850 0C
Observation port To be provided with protective glass type
     3.3    Secondary chamber

Supply, Installation and Commissioning of DIESEL FIRED INCINERATORS

Supply, Installation and Commissioning of DIESEL FIRED INCINERATORS
Medical Waste Incinerator, 100 to 120 Kg/hr
Application   For incineration, general and pathological
Capacity    100 C 120 kg/h burn rate
Type Two  combustion chambers type; primary  and Secondary, controlled/forced combustion air type with a flue gas emission scrubbing unit
Operating time                Minimum 8 hours daily
Operating temperature     From 850 0C to 1200 0C, Automatic controlled
Residual Ash                    5 to 10%
Construction Constructed from heavy duty mild or aluminized  steel
Or equal and approved equivalent

Insulation material            Refractory material lining similar or equal to calcium 
Silicate and hot face combination of heavy duty brickwork
Internal Construction        Fixed hearth type complete with gratings, concave bottom and charging door, lined with refractory material
Charging Door                   Suitable for manual loading of wastes and with smooth 
Dear seal equivalent of Ceramic seals with hinges.
Door Lock                          Automatic, Electric type
Ash removal door    Provided, for removing resultant bottom ash leftovers                              from the Primary chamber
Gratings    Provided
Loading Manual loading of waste
Primary Burner                        Fully automatic, with fuel, temperature and speed  controls with ignition system  flame detector                                                         Air fan Complete with safety features, flame failure                                                                    Diesel fired fuel injector type                                               
Flange mounted
Blower   Provided.  3 phase for supplying excess combustion air through the distribution system with speed control system
Temperature Minimum exit 850 0C
Observation port To be provided with protective glass type
     3.3    Secondary chamber

Incinerador de desechos médicos de aire controlado diseñado para la incineración de desechos biomédicos

Incinerador de desechos médicos de aire controlado diseñado para la incineración de desechos biomédicos generados en un centro de procesamiento de sangre. Los desechos a tratar incluyen principalmente biorresiduos (es decir, fluidos corporales), desechos infecciosos y peligrosos como jeringas, agujas y otros desechos médicos (es decir, cauchos de silicona, plástico, textiles, papeles, paquetes, etc.)

Especificaciones operativas Especificaciones físicas
Volumen de la cámara de combustión (m3) 8.80m3
Velocidad de combustión* hasta 1500 kg por hora
Consumo medio de combustible 65 kg por hora o más (7 quemadores diesel)
Temperatura operacional 850 – 1320 ° C
Retención de gas en cámara secundaria Gran cámara secundaria
Monitoreo de temperatura sí
Residuo medio de cenizas (%) 3%
Dispositivo termostático sí
Depósito de humos diesel 1000l
Depurador de gas Venture
Sistema de alimentación de ariete hidráulico
Incinerador grande con motor diésel
Especificación mínima requerida

Estándares
1) Licitante o fabricante con certificación ISO 9001
2) Respetando los estándares internacionales de emisión
Características electricas
3) Una fuente eléctrica monofásica de 230 V, 60 Hz.
4) Protecciones contra condiciones de línea de sobretensión y sobrecorriente.
5) Cumplimiento de las normas y reglamentos de Ghana aplicables.
Características operativas
6) Incineración en dos etapas con combustión de doble cámara
7) Tasa de combustión: 15-20 kg / h
8) Capacidad: no menos de 130 L
9) Concentraciones de la mayoría de los contaminantes en los gases de chimenea por debajo de los límites de detección
10) combustible diesel
11) Control del sistema electrónico
12) Fácil de operar y entrenamiento mínimo.
13) Cualquier accesorio o dispositivo dedicado necesario para el correcto funcionamiento y utilización del equipo incluido

CONSULTE LOS FOLLETOS ADJUNTOS PARA OBTENER ESPECIFICACIONES DETALLADAS

Controlled air medical waste incinerator designed for incineration of bio-medical waste

Controlled air medical waste incinerator designed for incineration of bio-medical waste generated at a blood-processing center. The waste to be treated mainly includes bio-waste (i.e. bodily fluids), infectious and hazardous waste such as syringes, needles, and other medical waste (i.e. silicon rubbers, plastic, textiles, papers, packs, etc.)

Operational Specs Physical Specs
Combustion Chamber Volume (m3) 8.80m3
Burn Rate* up to 1,500kg per hour
Average Fuel Consumption 65 kg per hour or more (7 diesel burners)
Operational Temperature 850 – 1320°C
Gas Retention in Secondary Chamber Large secondary chamber    
Temperature Monitoring Yes    
Average ash residue (%) 3%    
Thermostatic Device Yes  
1000l diesel flue tank
Venture gas scrubber
Hydraulic Ram Feeding System
Diesel Powered Large Incinerator
Minimum Specification Required

Standards1) Bidder or Brand ISO 9001 Certified2) Respecting international emission standardsElectrical characteristics3) A 230V, 60Hz single-phase electrical source.4) Protections against over-voltage and over-current line Requirements.5) Compliance with applicable Ghanaian standards and regulations.Operational characteristics6) Two-stage incineration with dual chamber combustion7) Burn rate: 15 – 20 Kg/h8) Ability: not less than 130 L9) Concentrations of most pollutants in stack gases under detection limits10) Diesel fuel11) Electronic Machine control12) Easy to operate and minimal training13) Any accessory or dedicated Apparatus necessary to the proper functioning and utilization of the equipment included

mit Dieselöl befeuerte Verbrennungsanlage für medizinische Abfälle

Hochtemperatur-Abfallverbrennungsanlage Modell D. MB 750XL Verbrennungsrate-150 kg / Stunde Mindestgewicht (kg) -4000 kg Sekundärkammer

(Doppelkammer mit Nachverbrennung) Gasretentionszeit 2 Sekunden Kraftstoff-Diesel-Netzteil für Steuerbox 220V-240, einfach

Phase 50-60Hz Minimale Betriebstemperatur 1200 oC Einjähriges Ersatzteilpaket für vollständige Wartbarkeit 10 m Schlauch

Rohr. 1100-Liter-Kraftstofftank + Rohrsystem Containerisiert (der Container dient als Gehäuse) Zusätzliche Kaminverlängerung

1 Meter hoch Ein (1) Jahr Garantie.

Verbrennungsanlage von 20 kg: 03 Einheiten

Elektrisch gesteuerte Verbrennungsanlage.

Zweikammerverbrennungsanlage mit einer Kapazität von 20 kg / Stunde.

Verbrennungsanlage mit geringen Wartungs- und Betriebskosten; Ausgestattet mit einem automatischen Bedienfeld und einfach zu bedienen

elektromagnetische Verriegelung der Tür.

Eine Hauptabfallreduktionskammer von 900 ° C. Eine postsekundäre Brennkammer aus Gasen, die in der Primärkammer erzeugt werden

mindestens 1100 ° C.

Kohlenstoffrückstände in Asche von weniger als 5 Gew .-% gemäß der europäischen Richtlinie 2000/76 / EG.

Mit feuerfester Auskleidung aus hochwertigeren Materialien
1 / Kosten für eine Verbrennungsanlage für medizinische Abfälle mit 200 kg / h.
2 / (CIF-Laufzeit) Versandkosten von der Fabrik zum Seehafen PAPUA NEW GUINEA in LAE, Provinz Morobe
3 / Kosten von 2 Kleeingenieuren für die Überwachung, Installation, Schulung unserer Ingenieure und die Beauftragung des Mediziners; Abfall

Verbrennungsanlage.

Fourniture, installation et mise en service des INCINÉRATEURS DIESEL

Fourniture, installation et mise en service des INCINÉRATEURS DIESEL
Incinérateur de déchets médicaux, 100 à 120 kg / h
Application Pour incinération, générale et pathologique
Capacité 100 C Vitesse de combustion de 120 kg / h
Taper Type à deux chambres de combustion; air de combustion primaire et secondaire, contrôlé / forcé avec une unité de lavage des gaz de combustion
Temps de fonctionnement Minimum 8 heures par jour
Température de fonctionnement De 850 0C à 1200 0C, à commande automatique
Cendres résiduelles 5 à 10%
Construction Fabriqué en acier doux ou aluminisé robuste
Ou équivalent et équivalent approuvé

Matériel d’isolation Revêtement en matériau réfractaire similaire ou égal au calcium
Combinaison de silicate et de face chaude de maçonnerie résistante
Construction interne Type de foyer fixe complet avec grilles, fond concave et porte de chargement, revêtu de matériau réfractaire
Porte de chargement Convient pour le chargement manuel des déchets et avec une
Cher équivalent des joints en céramique avec charnières.
Verrou Automatique, type électrique
Porte de retrait des cendres Fourni, pour éliminer les restes de cendres résiduelles de la chambre primaire
Grilles Fourni
Chargement Chargement manuel des déchets
Brûleur primaire Entièrement automatique, avec commandes de carburant, de température et de vitesse avec détecteur de flamme du système d’allumage Ventilateur à air Complet avec fonctions de sécurité, coupure de flamme Type d’injecteur de carburant diesel
Bride montée
Ventilateur Fourni. 3 phases pour fournir un excès d’air de combustion à travers le système de distribution avec système de contrôle de vitesse
Température Sortie minimum 850 0C
Port d’observation A fournir avec le type de verre de protection
3.3 Chambre secondaire

Controlled air medical waste incinerator designed for incineration of bio-medical waste

Controlled air medical waste incinerator designed for incineration of bio-medical waste generated at a blood-processing center. The waste to be treated mainly includes bio-waste (i.e. bodily fluids), infectious and hazardous waste such as syringes, needles, and other medical waste (i.e. silicon rubbers, plastic, textiles, papers, packs, etc.)

Operational Specs Physical Specs
Combustion Chamber Volume (m3) 8.80m3
Burn Rate* up to 1,500kg per hour
Average Fuel Consumption 65 kg per hour or more (7 diesel burners)
Operational Temperature 850 – 1320°C
Gas Retention in Secondary Chamber Large secondary chamber    
Temperature Monitoring Yes    
Average ash residue (%) 3%    
Thermostatic Device Yes  
1000l diesel flue tank
Venture gas scrubber
Hydraulic Ram Feeding System
Diesel Powered Large Incinerator
Minimum Specification Required

Standards1) Bidder or Brand ISO 9001 Certified2) Respecting international emission standardsElectrical characteristics3) A 230V, 60Hz single-phase Electric Supply.4) Protections against over-voltage and over-current line conditions.5) Compliance with applicable Ghanaian Criteria and regulations.Operational characteristics6) Two-stage incineration with Double chamber combustion7) Burn rate: 15 – 20 Kg/h8) Ability: less than 130 L9) Concentrations of most pollutants in stack gases below detection limits10) Diesel fuel11) Electronic system control12) Easy to operate and Nominal training13) Any Attachment or Committed device Required to the proper functioning and Usage of the equipment Comprised