Tag: waste

waste

a complete destruction of waste from various hospital services

Jun 24, 2021 by hiclover 0 Comments #burner, #capacity, #chamber, #control, #door, #English, #fuel, #incinerator, #medical, #operation, #primary, #secondary, #temperature, #type, #waste
Medical Waste Incinerator Purpose
For a complete destruction of waste from various hospital services by heat treatment of high temperature in accordance with EU standard on emission requirement.
-Waste from health care activities
-Infections waste, laboratory cultures, waste form operation room isolations material in contact with infected patients, waste potentially being infected by pathogenic agents. 
-Pathological waste, human fragments, blood, fetus, all body fluids, human tissues.
-Sculpts, needles, infusion sets, blades, glass
-Pharmaceutical waste. 
-Chemical waste laboratory reagents, disinfectants
-Expired drugs. 
-Low radiation radioactive element.
Medical waste incinerator: – Ecological Requirement
– No odor
-No fume
-Definitive treatment of waste
Medical waste incinerator: – Manufacturing Standards 
-UL,CE, ASME, ISA EURO emission standard 
1.Medical waste incinerator 
Construction – CS plate shells, FB reinforcement, cast refractory linings, 
                        Insulation and 14 gage aluminum jacket. 
Type of fuel – Oil fired (Diesel)
Burning Capacity – 250kg/hr and moisture up to 80%.
Duration -8-16/Continuous  
Average fuel consumption – Very little as much as possible
Control Type – PLC based operation
Operating Temperature – Primary chamber 800oc ± 50
                                     – Secondary Chamber 1050oc ± 50
Size of incinerator – Not more than 15mx7.20m
Chimney – Ø630x25meter height  and 7mm thick CS.
Combustion efficiency- 99%
Mode of waste handling- Semi-automatic via ram loader.
Mode of ash handling – Semi-automatic via grate and ash trolley.
Pollution control equipment- Dry settlement zone
Doors- 1-waste charging door in primary chamber
            1-clinker door in primary chamber
            1-ash trolley access door in primary chamber
            1-clean out door in secondary chamber
Burner – 2- ignition burner in primary chamber
               2- after burner in secondary chamber.
            Type- package mono block-fully automatic
Type of burner operation- modulation control
Forced draught fan- 1-primary air fan
                                1-secondary air fan
             
Fuel storage tank – Capacity- 2500liter above ground
                             – Material-6mm thick mild steel
                             – 2-diesel pump, gate valve, safety valve, strainer
                                Pipe, pressure gage, check valve, control board
                                Level indicator. Etc
Refractory/insulation thickness- not less than 225mm
Ram loader capacity- 0.75m3
Electrical supply- 380v/3ph/50 Hz
Finish and painting type- powder coated 
Audio/ visual alarm system- burner lockout, overload fault 
Electrical accessories- primary and secondary chamber temperature 
                                  Controller/indicator, auto controls, electrical 
                                  Control switches, push buttons, relays, contactors
                                  Thermocouples, burner sequence controllers,
                                  Timers, emergency stop and alarms.
Zhangjiagang Tengxiang Machinery Co., Ltd.
Mobile: 0086-13962221749(whatsapp)
Wechat: chncheumg
Face Mask Machine for Coronavirus Disease COVID-19

平面口罩机参数：

Semi-Automatic Mask Machine

l Power supply: 3.3KW mono phase

l Mask Size: 175mm*80-100mm (two or three layers)

l Nonwoven (GMS): 10-50g

l Capacity: 120 to 150pcs/min

l Dimension(L*W*H):3800mm*500mm*1400mm

l Net Weight: about 1000kg

 

焊接机参数：

Welding Machine

l Capacity: 5 to 10pcs/min

l Power supply: 8.5KW mono phase

l Compressed Air connection: 0.5 to 0.7Mpa

l Dimension(L*W*H): 900mm*650mm*1380mm

l Net weight: approx. 50kg

 

KN95口罩机参数：

N95 Mask Machine

l Capacity: 130 to 160pcs/min

l Dimension(L*W*H): 1037*855*1780

l Power Supply 15.3kw mono phase

l Net Weight: approx.: 1500kg



HICLOVER – Medical Environmental 

 

Waste Incinerators
Medical Waste Incinerator
Pet Animal Cremation
Solid Waste Incinerator

Tel:  +86-25-8461 0201   
Mobile: +86-13813931455(whatsapp/wechat)
Website: www.hiclover.com  
Email: [email protected]
Email: [email protected]  
Nanjing Clover Medical Technology Co.,Ltd.

 

2020-04-06

N95 Face Mask Machine Production Line on Sale Now! $250,000USD per set

N95 Face Mask Machine Production Line on Sale Now! $250,000USD per set

l Dimension(L*W*H): 1037*855*1780

l Power Supply 15.3kw mono phase

l Net Weight: approx.: 1500kg

HICLOVER – Medical Environmental 

 

Waste Incinerators
Medical Waste Incinerator
Pet Animal Cremation
Solid Waste Incinerator

Tel:  +86-25-8461 0201   
Mobile: +86-13813931455(whatsapp/wechat)
Website: www.hiclover.com  
Email: [email protected]
Email: [email protected]  
Nanjing Clover Medical Technology Co.,Ltd.

 

2020-04-10

we are portable incinerator manufacturers, the Mobile Containerized Incinerator, moveable for truck, buring rate upto 100kgs per hour. We design for end customer, we dispatch for better services.

Model CA50
Feed Capacity Average 60 kgs per feed
Burning Rate Average 70 kgs per hour
Burning Time per Feed 1 hour
Voltage 220V
Power 0.7Kw
Fuel Diesel oil
Burner Italy Burner
Feed Mode Manual
Fuel consumption (Oil) Average 18 Kgs/Hour
Internal Dimensions 100x80x70cm (Primary Chamber)
External Dimensions 230 x 130 x 155cm (main body)
Waste combustion chamber 560Liters
Post Combustion Chamber 280Liters
Oil Tank Capacity 100 Liters
Door Opening 70 x 50cm
Chimney 5.0M
Gross Weight 4500kgs
Chamber Material Firebrick ,Refractory Concrete
Max. Heat Value 240,000Kcal/Hr.
Operation Technical Specifications
Solid Chamber temperature 8000C -10000C
Gas Chamber temperature 10000C -12000C
Chamber Anti-Rate 14500C
Residency time 2.0 Sec.
Burning efficiency ＞98%
Waste Lower Calorific Power 3000Kcal
waste

INCINERATOR SPECIFICATION Capacity UPTO 20 kg/hr

Jun 22, 2021 by hiclover 0 Comments #above, #chamber, #during, #easy, #English, #incinerator, #international, #least, #lining, #material, #per, #standards, #temperature, #waste
Size:  940 x860x2700 mm
Material:  STAINLESS STEEL STACK, REFRACTORY CONCRETE LINING SPECIAL INSULATION MATERIAL
With burner:  15 C 20 KW
Temperature:   PRIMARY CHAMBER = 800°C AND SECONDARY CHAMBER = 850 – 1200° C
Sufficient heat generation for secure and complete combustion 600-800 °C in the first chamber and >1000 °C in the second chamber
Easy transportation on standard EURO-pallets
Constructed in a modular fashion  easy on-site movement and assembly with a minimum of equipment and technical skills;
For the destruction of problematic waste like sharps, amputates and body parts, wet or moist matter;
Off-gas quality: moderate smoke emissions during one quarter of the total incineration time; no visible emission during three quarters. AS PER INTERNATIONAL STANDARDS 
The remaining ash approximately 5-10% in weight and below 1% in volume of the original waste AS PER INTERNATIONAL STANDARDS 
Chimney height at least 5 m above the incinerator 5m ABOVE FROM THE GROUND
Temperature resistance of the lining  at least 1,200 °C
waste

INCINERATOR SPECIFICATION Capacity UPTO 20 kg/hr

Jun 22, 2021 by hiclover 0 Comments #above, #chamber, #during, #easy, #English, #incinerator, #international, #least, #lining, #material, #per, #standards, #temperature, #waste
Size:  940 x860x2700 mm
Material:  STAINLESS STEEL STACK, REFRACTORY CONCRETE LINING SPECIAL INSULATION MATERIAL
With burner:  15 C 20 KW
Temperature:   PRIMARY CHAMBER = 800°C AND SECONDARY CHAMBER = 850 – 1200° C
Sufficient heat generation for secure and complete combustion 600-800 °C in the first chamber and >1000 °C in the second chamber
Easy transportation on standard EURO-pallets
Constructed in a modular fashion  easy on-site movement and assembly with a minimum of equipment and technical skills;
For the destruction of problematic waste like sharps, amputates and body parts, wet or moist matter;
Off-gas quality: moderate smoke emissions during one quarter of the total incineration time; no visible emission during three quarters. AS PER INTERNATIONAL STANDARDS 
The remaining ash approximately 5-10% in weight and below 1% in volume of the original waste AS PER INTERNATIONAL STANDARDS 
Chimney height at least 5 m above the incinerator 5m ABOVE FROM THE GROUND
Temperature resistance of the lining  at least 1,200 °C
waste

chinese incinerator manufacturers

Jun 22, 2021 by hiclover 0 Comments #chinese incinerator, #hospital incinerators, #incineration, #incinerator, #incinerator manufacture, #incinerator manufacturer, #incinerator manufacturers, #medical incinerator, #mobile incinerator, #nanjing clover medical technology, #waste, #waste-incinerator


chinese incinerator manufacturers

wea are chinese incinerator makers.  Nanjing Clover Medical Technology Co., Ltd..  Is a leading waste incinerator maker in China. All show comprised burning capability 10kgs per hour, 30kgs per hour,50kgs each hour,100kgs each hour,150kgs each hour,300kgs each hour,500kgs per hour. So far, all versions sale to all around the world and also have good feedback from end-customer. The YD Model medical incinerator possess multi-combustion room and fundamental dry scrubber (smoke filter chamber) with reasonable endeavor budget. For the cleaner require, we take custom made wet scrubber for incinerator, which will be also our following functioning by focusing on emission technical.

Dual Combustion Chamber: Each of waste incinerator layout with double glazing chamber. High Temperature, Smoke Treatment，No black smoke, Environmentally friendly

Containerized Mobile Incinerator: The incinerator mounted in ISO Container before leave mill, free-installation, no incineration house build structure,movable by truck.

Family Pet Dog&Cat Cremation: Particular design with movable platform, combustion chamber material and custom made for pets crematory enterprise.

Installation and Commissioning: Clover’s engineers instal,train for most of the region and free-cost train in our mill.

waste

Incinerator with Capacity of destruction in weight: 60 Kg/h.

Jun 21, 2021 by hiclover 0 Comments #able, #burner, #capacity, #chamber, #combustion, #destruction, #door, #English, #incinerator, #kg, #loading, #must, #refractory, #should, #waste, #weight

Capacity of destruction in weight: 60 Kg/h.

It should be able to operate not less than 10 hours/day

This incinerator must be able to destruct all combustible wastes produced by hospitals, private clinics, laboratories, institutes, etc…

Design Specification : Types A, B, C, D, and E of medical waste 

“PYROLYTIC” combustion, by controlling the gasification of waste.

The incinerator must avoid the release of black smoke and fine dust, (Smokeless) during the loadings.

It should be able to reduce the volume of wastes by 98%.

It should be able to hold emission in the second burn with gas residence of not less than 2 seconds.

The incineration should be completely free from visible smoke as well as offensive odours.

The lower calorific power (L.C.P) of this waste will be 3,500 kcal/kg

The Temperatures of combustion: Minimum will be 850oC and max 1400oC

Post combustion: >1100oC.

The Internal diameter of the Chimney: Ø 400 and its height: 8 m

The Volume of the combustion chamber: 1.200 L

The Dimension of the door for loading in cm: 70×70.

Burner operation should be Automatic On/Off

Fuel : diesel

The supplier must provide  necessary information for the best of  the installation

This incinerator with “PYROLYTIC” combustion must have:

A combustion chamber of waste:

* Perfectly tight door for the manual loading of waste. The loading should be Manual, Batch Load 

* A burner of lighting which the use is limited to the ignition of waste.

* Frontage of loading with door seals gone up on hinges, wheel of screw plug, flexible joint, and stuffing insulating out of refractory.

* The insulation of the combustion chamber should be composed of refractory bricks, having a high content of aluminium and insulates bricks in order to assure a minimum temperature on   the outside sheet metal.

* Composition of the refractory;

Refractory concrete :

. Thickness : ≥100 mm

. Nature: 42% of Al203

Insulate in fibrous panels :

. Thickness: ≥75 mm

Nature: Calcium silicate.

* Burner of lighting of waste, with fuel, standard mono-bloc casting guiding  plunging flame, lighting and safety of electronic ignition, permanent ventilation, electromagnetic sluice gate of regulation and isolating valve.

* Plate of combustion in Carborundum, avoiding the fixing of glass and slags. 

1. N95 and Disposable Mask Machine

 

2. 400mm and 1600mm Melt blown Production Line

3. ES Fiber Production Line

 

 

 

N95 Face Mask Machine Production Line

Melt blown Production Line

 

A.)Optional Capacity: 1600mm

Efficiency: 95-97%

FOB Term Price: USD per set

Price Valid: 5days.

Ave.60 Days ready for shipping.

In stock Price: USD per set

 

 

B.)Optional Capacity: 400mm

Efficiency: 40-50% .

FOB Term Price: USD per set

Price Valid: 5days.

Ave.20 Days ready for shipping.

Payment: TT 70% In advance, TT 30% before leave factory

Shipping: 1*20′ container per set, Ave. 2000Kgs.

 

Main Parts: Extruder, mold, winder, oven, ultrasonic

Daily Capacity：100-150Kgs/24Hours

Screw extruder：100-150Kgs

Motor power: 15KW frequency conversion speed regulation
Reducer speed ratio: 1:10 or 1:16
Screw length to diameter ratio: 30: 1
Screw diameter: 50mm
Winding machine diameter: ￡ 630mm
Winding machine drive motor power: 0.55kw
Speed ratio of winder drive reducer (if any): 1:71
Air heater power: 15kw
Power of vacuum calciner: 12kw
The size of vacuum calciner: 500 × 300 × 200
Ultrasonic power: 1800, frequency 28kHZ
Ultrasonic sink size: 800 × 300 × 250

 

 



HICLOVER – Medical Environmental 

 

Waste Incinerators
Medical Waste Incinerator
Pet Animal Cremation
Solid Waste Incinerator

Tel:  +86-25-8461 0201   
Mobile: +86-13813931455(whatsapp/wechat)
Website: www.hiclover.com  
Email: [email protected]
Email: [email protected]  
Nanjing Clover Medical Technology Co.,Ltd.

 

2020-04-20