Archive: September 19, 2024

pet crematorium equipment

Finally, steam to  the jacket should shut off, the unloading door is to be opened

Then the shaft and mixing arms are reversed to act as unloading mechanism and should scoop the waste fragments out of

the unloading door, onto a conveyor belt or directly into a waste container.

The vessel should now be ready for another treatment cycle, having retained most of its heat for the treatment of the

next batch.

(B)Features and Specification of the Steam Boiler:

Features of the Boiler:

It must be an Electrical boiler

Splash proof electric enclosure and switches

Door Isolator to main electric enclosure

Alarm lights and Safety/protection against excel pressure

Level control on feedback water tank

Technical specification of the Boiler:

Output: between: 90-110 kg/h (F&A 100 deg C)

Working pressure: between 7-10 bar

Boiler water content: between 80-100 liter

Feed water tank content : between 60-80 liter

Power consumption: between 60-75 Kw

Number of Heating Elements: 3-4 nos.

Electrical requirements: 400Vac, 50 Hz, 3 ph

(C)Technical Specifications of Tub washer

Features:

Fully automatic and manual modes.

Metal construction, SA 240/304

Sensors to maximize both machine efficiency and operator safety.

Must use Re-circulating cold wash water to minimize water consumption and operating costs

Disinfects all bin surfaces

Uses Powerful blow dryer to remove excess surface water

Must be compliant with all North American and EU regulations

Specifications:

Tub washer able to wash bins of a suitable size , the norm being 38 g

Must have an water reservoir of capacity minimum : 225 liter

Perfectly suited for hospitals and clinics by processing up to min.300 bins per hour.

Time to wash and dry one bin after loading-approximately 12 nos.

Bins loading on wash station at a time -approximately 12 nos.

Overall length: approx 30.0 feet

Overall length: approx 8.0 feet

Overall length: approx 3.0-3.5 feet

Height to Conveyer from ground: approx 3 feet.

Drive of the Tub washer

Motor driven

Motor Horsepower : approx. 4.0 HP

Power : 220vac, 1 ph or 400 VAC , 3 ph or to suit customer needs

Bins to be included

200 nos. with different color (based on the actual requirement of the hospital)

(D)Technical Specification of External SHREDDER Controls

Pre-programmed PLC controlled

Password activated and reversal history indication

Motor starter with overload protection

Automatic instantaneous stop on hard object in shredder bed

Automatic heavy cutting load reversal and re-try , up to three times

Control housing Nema Type 12

Cutting Hardwires

Chamber Dimensions (W x L x H): approx. 33 cm x 38 cm x 25 cm

Number of Knives: approx 18 or to suit customer needs

Knife Thickness : approx 18 mm or to suit customer needs

Knife Diameter : approx 16 cm or to suit customer needs

Teeth per Knife: minimum 3

Number of Shafts : 2 ie double shaft shredder

Drive of the shredder

Must be motor driven

Motor Horsepower: approx. 10 HP

Motor RPM: minimum 1750

Speed Reduction : 60:1

Generated Torque : min 40 Nm or 350 Ibs/in.

Gearbox: should be Parallel shaft

Shock Protection: Rubber Mount Torque Arm

Power: 220vac, 1 ph  or 400 VAC , Ph or to suit customer needs

Ancillaries to be included

Shredder stand, fabricated from 3” sq. steel tube, standard height 30 inches

Shredder hopper , fabricated from 16 gauge steel, with optional switched hopper lid

(E)Features & Technical Specification of Conveyer

To carry processed waste from vessel to shredder

Controls

Motor starter with overload protection

Control housing Nema Type 12

Safety pull-stops along both sides of conveyer

Ancillaries

Conveyer stand, fabricated from 2” sq. steel  tube

Raised sidewalls fabricated from 16 gauge steel

Dimensions

Over-all length: between 20-25 feet or appropriate length depending on the installation requirement.

Over-all width: between 24-30 inch

Over-all height (without including stand): between 12-14 inch

Available inclines:    0-40 degrees

Belt Speed: 75 ft/min

Dam spacing: approx. 16 inch

Drive

Motor driven

Horsepower :approx. 0.75 HP

Motor RPM: approx. 60

Electrical Power input : 220vac, 1phj or 400 VAC , 3 Ph or to suit customer needs

(F)Technical Specification of Tipper

Features:

It is to be designed to allow for easy bin positioning under the door to unload processed waste and easy

maneuverability for lifting and tipping the waste into the shredder hopper.

Equipped with 2 binds to accommodate processed waste loads to be loaded into the shredder and shredder waste to be

transported to the disposal bin.

Frame: Rugged heavy duty frame constructed of formed and welded steel for extra strength

Mast: Fabricated with cannel steel for greater strength and dependability. Open structure design complete with safety

cage to offer greater visibility.

small incinerator for sale

Sterilization time: approx. 30 minutes at 121◦C/1.1 Bar or approx  15 minutes at 132◦C/2.5 Bar to achieve 6log10

sterility

Fragmentation inside the chamber: Heavy duty with maximum size of final product <20 cm.

Volume reduction of the waste after processing : by 60-80% through complete waste dehydration including liquid

content of the waste

All actions after loading for sterilization, fragmentation of product is to be occurred in the same chamber/vessel

Pre or Post-air evacuation should not be necessary or used

Exhaust air quality : Does not require any venting for odor control

Operating System: Fully automated with manual over-ride .(On board PLC capable of generating written report with

cycle time , cumulated time at >121◦C

The option should be there for Internet connectivity by phone, cable or

Boiler : should not require pre-heated water

Electrical requirements: 220Vac, 1ph or 400vac 3ph to suit customer needs

Noise level at full operation: <80 dB

Working Principle of the processor

The processor should utilize steam technology in conjunction with a mechanical fragment (grinder) to sterilize

medical waste, thereby making the residual waste safe for disposal in landfills.

The sterilization vessel MUST be a double walled (jacketed) cylindrical vessel.

Pre-shredding of infectious waste must not be accepted, the fragmentation must occur safely inside the scaled vessel

continuously.

The sterilization vessel/chamber must be fitted with a motor driven shaft to which a heavy duty grinder (fragmenting

arm) is attached inside the vessel to produce an unrecognizable size of the waste product

The fragmenting are must rotate to agitated continuously throughout the heating and sterilization cycle to ensure

that the fragmented & agitated wastes (including sharps and liquids) are exposed evenly to sterilization temperature

and pressure.

Steam heat should be applied to the jacket only, while the agitated waste absorbs the heat from the jacket and makes

its own steam from its moisture content.

Should not need for special autoclave bags- simple bag or box should be workable

MUST not need for pre-treatment of the waste.

Liquids and gases MUST remain locked inside the vessel until sterilization is complete-nothing should be vacuumed or

pumped out in its infected state.

Jacket steam heat to dehydrate the waste completely regardless of its original water content.

All the hot condensate from the jacket is recycled, making the processor very economical to operate

All particles of the waste should achieve a high level of sterilization and not just “disinfection” due to the

continuous agitation.

Description of the Treatment Cycle of the processor

i)Loading

The waste has to be loaded by dropping bagged and or boxed waste into the open loading door on the vessel.

The loading door should be mounted at an angle on the top side of the vessel with suitably sized to accommodate the

infectious wastes for which it is intended

Over-loading or loading too tightly should not be an issue with this process, and hence no need of the special

operator skill.

ii)Heat –up and fragmentation

After loading , the vessel door is to be closed, and the outer jacket of the vessel is to be automatically filled

with high temperature steam, which should act as the main heating medium for heating the waste

During this heating cycle, the shaft and mixing arms should rotate continuously, causing the waste to be fragmented

and continuously tumbled against the hot vessel walls.

At this point, the waste is broken up into small fragments, and all material heats up rapidly, being evenly and

thoroughly exposed to the hot inner surfaces. The moisture content of the waste will turn in to steam, and the vessel

will start to pressurize.

Initially, no steam will be injected into the waste. If there not enough moisture in the waste to pressurize the

vessel, a small amount of steam is to be automatically added until the desired pressure is reached.

At the end of the period, the correct sterilization temperature and should be reached, and the sterilization period

should start.

iii)Sterilization period

The amount of steam fed to the outer jacket is to be regulated to maintain the desired temperature & pressure of the

inner vessel.

The mixing arms (grinder)  MUST continue to rotate throughout this cycle to ensure even sterilization pressure and

temperature for all wastes.

The treatment time should be either 15 minutes at 132◦C OR 30 minutes at 121◦C  to achieve level 6log10 sterilization

The intense subjugation of the waste to high temperature and pressure moisture in a dynamic environment should also

cause the waste to hydrolyze, that is a rapid decomposition of organic material.

iv)De-pressurization

After the treatment time , the steam to the jacket should remain on, and the internal vessel is to

be vented through a condenser, and de-pressurized. Thus, the waste loses its water content

through a combination of heat input from the jacket and flashing of water due to

depressurization.

v)De-hydration

Further dehydration is to be achieved by maintaining heat input and mixing-almost total dryness should be achieved.