Archive: August 10, 2023

hazardous waste incinerators in china

Anchor all equipment to building floor or structure as shown or as recommended by manufacturer with allowance

for thermal expansion as necessary.

1. Control and Instrument Panel: Rigidly attach enclosure to structural element of the building. Locate panel so

that all control switches and indicators are within 1700 mm (5.5 feet) of the floor and are located alongside the area

where personnel will be loading the unit.

1. Clean interior and exterior of all equipment before placing in service.

1. Initially operate incinerator at firing rates and time periods recommended by the manufacturer of the

refractory to provide proper curing of the refractory. Provide printed curing instructions from refractory manufacturer

at the site prior to first start up.

1. Personnel Protection for High Surface Temperature: If incinerator has surface temperatures exceeding 40 degrees

C (70 degrees F) above ambient, provide removable chain barricades mounted on 1070 mm (3 1/2 feet) high removable steel

posts spaced 1200 mm (four feet) on centers. Locate barricade at least 900 mm (three feet) away from hot surfaces.

Provide yellow polyethylene chain with removable hooks at each post. Provide sign attached to each chain reading,

“Caution, High Temperature”.

1. Do you have model YD-500 as a mobile unit? In case of a major crisis in one of the clusters we would like to have

the option to move the unit closer to the location to avoid transporting the dead cows. Do you have any mobile

solution?

2. Please elaborate what additional equipment we will need to buy to operate each unit? I need to know the total cost

per unit.

3. Does the unit need to be under a roof?
4. How is the loading of the dead cow into the incinerator done?
5. How is the incinerator emptied?
6. Are there any limitations on how we should dispose the remains from the incinerator?
7. Does the unit require a dedicated trained operator? How long does it take to train one?
8. Do you send your engineer for installation, commissioning and operation?
9. Assuming we have 3 dead cows a day per incinerator – how many hours a day it would take to complete the job?
10. In case of crisis can the unit work continuously 24H a day?
11. Is there any impact of smoke or smell on the surrounding?

3.2        INSPECTIONS AND TESTS:

1. General: Demonstrate to the Department of Veterans Affairs that all equipment complies with requirements. The

Contracting Officers Technical Representative (COTR)/Resident Engineer (RE), or their representative shall witness all

tests. Representatives of the pollution control authority that has jurisdiction shall also witness emissions tests.

Provide two weeks advance notice to the COTR/RE of all testing. Pretest all items prior to the final testing that is

witnessed by the COTR/RE.

1. Condition of Equipment after Delivery, Rigging, Placement: After setting equipment on foundations, and prior to

making any connections to equipment, the Contractor and COTR/RE jointly shall inspect interior and exterior for damage.

Correct all damage by repair or replacement to achieve a like new condition.

incinerator type of pyrolytic medical waste incinerator capacity

Including:Incinerator: Structure to be specified
The mark to be specified
Water temperature: 800 to 1000 ° C;
Refractory
Temperature of more than 1100 ° C + obtained;
Capacity: 20-50 kg / hour
Fireplace: 4 to 6 meters high;
Dimension 70 cmx70 crn
Height: 1.10 meters
Fuel: coal;
Aspiration: natural

– A receiving cage for biomedical waste;

– A combustion chamber with a chimney with a filter to retain the ashes;

Chimney section: about 300 cm; With a minimum height of 6 m

Door size: approximately 50×60 cm

Supplied with a 500 liters fuel tank and all necessary accessories for installation.
–                          INCINERATOR for pharmaceutical waste treatment with                  a scrubbing system

With the following technical data:

1.      One pharma solid waste incinerator unit containing two combustion chambers and based on steel base with scrubbing

system.

2.      Working hour /day: minimum 10 hours/day.

3.      Capacity: Approximated 150 kg/hr. Over 10 hrs.

4.      Wastes characteristics:

·         BULK density: 70 – 100 kg/ bm³.

·         Calorific value: 2000-3000 kcal / hr.

·         Moisture content: 20-30%by weight.

·         Ash content: 2 – 8 % by weight.

·         Plastic content: 15-20 % by weight.

5.      Two combustion chambers.

6.      Operating temperatures:

·         First chamber: not less than 700 – 800 °c.

·         Second chamber: not less than 1200 °c (during steady operation).

7.      The burners should be automatically switched off if any of the combustion chambers doors is open.

8.      The burners of the first and second combustion chambers are selected for burning diesel oil (light fuel).

9.      Automatic loader and unloader to be provided.

10.     Exhaust gases to be comply with International Environmental code and requirements.