Tag: incinerator

diesel oil fired medical waste incenerator

Heat Waste Incinerator Layout D. MEGABYTES 750XL Melt Rate-150Kg/ hr minimum Weight( Kg) -4000 kg Added Chamber

(double chamber with post-burning) Gas Retention Time 2 2nd Gas Diesel Power Supply for control box 220V-240, solitary

phase 50-60Hz Minimum operating temperature degree 1200 oC One year extra parts bundle for full maintainability 10m pipe

pipe. 1100 litre fuel Storage tank +pipeline system Containerised (the container will definitely function as housing) Added smokeshaft development

1 metre high One (1) year warranty.

Heater of 20 Kg: 03 Gadgets

Electrically controlled burner.

Two-compartment heater with a capacity of 20 kg/ hour.

Burner with minimized upkeep as well as operating expense; Prepared with an automated control board as well as very simple to utilize with

electro-magnetic securing of the door.

A major waste decline chamber of 900 ° C. A post second burning chamber of gases developed in the main chamber

at the minimum 1100 ° C.

Carbon deposits in ash much less than 5% by weight in accordance with European Directive 2000/76/ EC.

With refractory cellular lining in products of better
1/ Cost of a 200kgs/Hr medical waste heater.
2/ (CIF Term) Cost of distribution from making center to PAPUA NEW GUINEA port of LAE, Morobe district
3/ Cost of 2 Clover engineers to Oversee, Setup, Educating our engineers and designating the clinical; waste

incinerator.

burner kind of pyrolytic clinical waste burner capacity

Including:Incinerator: Structure to be specified
The mark to be specified
Water temperature: 800 to 1000 ° C;
Refractory
Temperature of more than 1100 ° C + obtained;
Capacity: 20-50 kg / hour
Fireplace: 4 to 6 meters high;
Dimension 70 cmx70 crn
Height: 1.10 meters
Fuel: coal;
Aspiration: natural

– A receiving cage for biomedical waste;

– A combustion chamber with a chimney with a filter to retain the ashes;

Chimney section: about 300 cm; With a minimum height of 6 m

Door size: approximately 50×60 cm

Supplied with a 500 liters fuel tank and all necessary accessories for installation.
–                          INCINERATOR for pharmaceutical waste treatment with                  a scrubbing system

With the following technical data:

1.      One pharma solid waste incinerator unit containing two combustion chambers and based on steel base with scrubbing

system.

2.      Working hour /day: minimum 10 hours/day.

3.      Capacity: Approximated 150 kg/hr. Over 10 hrs.

4.      Wastes characteristics:

·         BULK density: 70 – 100 kg/ bm³.

·         Calorific value: 2000-3000 kcal / hr.

·         Moisture content: 20-30%by weight.

·         Ash content: 2 – 8 % by weight.

·         Plastic content: 15-20 % by weight.

5.      Two combustion chambers.

6.      Operating temperatures:

·         First chamber: not less than 700 – 800 °c.

·         Second chamber: not less than 1200 °c (during steady operation).

7.      The burners should be automatically switched off if any of the combustion chambers doors is open.

8.      The burners of the first and second combustion chambers are selected for burning diesel oil (light fuel).

9.      Automatic loader and unloader to be provided.

10.     Exhaust gases to be comply with International Environmental code and requirements.

lab incinerator china producer

Incinerator double chamber with capacity 1.5 m3/batch or 6 m3/ day, digital thermocontrol array 0‐1200

C, thermocouple, air supply capacity 10m3/ min, power use 1.2 kWH/ hr, power 3

stage with netral, cooling water sprinkler ability 5L/ minute, finished with refractory (insulation,

castable, ceramic covering) and also PLC

SUPPLY, INSTALLMENT In Addition To COMMISSIONING OF WASTE HEATER– – TECHNOLOGICAL SPECIFICATIONS

The Waste Incinerator is developed to melt Type IV of pathological waste as well as contagious, contaminated “red bag,” surgical

dressings, plastic exam gadgets as well as also numerous other wastes.
General Specifications
Burner: 2 heating units (key heating unit in addition to 2nd heater).
Fuel: Oil.
Capability (Cubic Mtr): 0.65.
Ave Capacity: 60 kg per hr.
Gas Consumption (ltrs/ human resources):13.
Outside Measurements.
Size (mm): 2300.
Size (mm): 1220.
Elevation Incl. Flue (mm) 7000.
Door Opening (mm) 610 x 710 610 x 710.
Procedure.
Minutes. Running Temperature degree: 950.
Max. Running Temperature level: 1320.
Residency Time in Secondly Chamber: 5 sec.
Temperature Level Monitoring: YES.
Various various other details.
Easy and also safe operation.
Massive counter-balanced fill door with electric lockout.
Automatic control system offers predetermined close and thaw times down.
When it is time to recharge, Reload light shows to driver.
Be needed for fatigue of last cost.
Low power use degrees.
Programmable electronic temperature level controls preserve temperature level, ensuring complete combustion while saving fuel.
Tension blower with managing air control develops disturbance along with disperses melting air to additional chamber.
2nd heating unit with temperature triggered modulating control offers quickly preheat as well as maintains heat

efficiency at low power usage levels.
Billing cost

clinical facility incinerator manufacturers

SCHEDULE 2

• TECHNICAL SPECIFICATIONS OF THE INCINERATOR

• General Description

Previous experience in the supply, installment as well as appointing of burners

1. Overall plant layout
2. Feed chamber/charging
3. Primary combustion chamber
4. Particulate scrubbers
5. Acid gas
6. The stack/chimney.
7. Minimum capacity of primary chamber = 10cubic meters
8. Burn rate (rate of waste incineration) = 10 kg per hour
9. Should have a full width counterbalance loading door allowing easy access to the main chamber for loading and removing ash.
10. The INCINERATOR should be NEMA approved in accordance with Environmental management and coordination (Waste management) Regulations of 2006.

• Scope Of Work

at least10kg per day

1. Supply, install and commission an incinerator as provided   in the technical specifications

2. Provision for adherence to OSHA and other statutory requirement relating to Health and Safety of workers during execution of the works covered in this

3. Assessment and preparation  and construction of  a standard incinerator shed with one waste  storage room  ( see the design )

4. Provision of operation and maintenance manuals and drawings complete with maintenance schedule and

5. Fuel oil storage tank- Mild steel 1000 liters capacity

6. Onsite training for operation and maintenance

Basic Strategy design to Supply Overall plant layout.

Genuine estate center with one waste storage room

Deal Real estate designs with ideal cross air circulation

3. TECHICAL SPECIFICATIONS OF THE INCINERATOR

Chamber (Afterburner Optimum departure temperature must not be much less than 1100oC

Security interlock, Fan Newbie, Heating System on/ off switch/door safety button, Vehicle layer button, temperature levels regulate device.

• Primary Combustion

• This chamber should be equipped with burners that use low sulphur
• The chamber should ensure a minimum exit temperature of 850 degrees
• This unit should operate at over 1100 deg C to ensure complete
• This chamber should be equipped with burners that use low sulphur
• Heavy-duty steel casing
• High quality refractory lining and insulation
• Large full size top load door and liquid retention
• 1 x oil fired ignition burners operated on/off

• Secondary Combustion Chamber (After burner)

1. Heavy-duty steel casing
2. High quality refractory lining and insulation
3. 1 x oil burner
4. Should be fitted with burners that use low sulphur
5. Ensure secondary air supply is controlled.
6. Ensure residence time is not less than two seconds.
7. Ensure that the gas temperature as measured against the inside wall in the secondary chamber and not in the flame zone is not less than 1100 degrees
8. Ensure the emitted oxygen content of the emitted gases is not less than 11%
9. Ensure both primary and secondary combustion temperatures are maintained until all waste is completely

• Particulate Removers

Key Combustion Chamber Minimum departure temperature level need to not be much less than 850oC

1. Cyclone separator
2. Electrostatic precipitators
3. Fabric filters

• Chimney/Stack

1. The chimney should have a minimum height of 10 meters above ground level and clear the highest point of the building by not less than 3 meters for all The topography and height of adjacent buildings within 50 meters radius should be taken into account.
2. The chimney should be visible to the operator from the feeding

1. The minimum exit velocity should be 10 meters per second and at least twice the surrounding wind speed (Efflux velocity = wind speed x 2) whichever is higher to ensure no down washing of exiting
2. The point for measurement of emissions shall be

• Instrumentation

1. Instrument for determining the inside wall temperature and not burner flame temperature must be provided for both primary and secondary
2. An audible and visible alarm must be installed to warn the operator when the secondary chamber temperature drops to below the required
3. A carbon monoxide and oxygen meter/recorder should be
4. A smoke density meter/recorder should be
5. A solid particulate meter/recorder should be
6. Any other instrument that may be considered

• Location / Siting of the Incinerator

1. a) The incinerator must be sited in accordance with the relevant local municipal authority planning regulations and the topography of the site must be compatible with premises in the

• Emission Limits

99. Combustion efficiency (C.E) shall be at least00% where C.E = %Carbon dioxide x 100 / [% Carbon dioxide + carbon monoxide]
100. The temperature of the primary chamber shall be 800 +/- 50 degrees centigrade
101. The secondary chamber gas residence time shall be at least 1 second at 1050 +/- 50 degrees centigrade with 3% oxygen in the stack
102. Opacity of the smoke must not exceed 20% viewed from 50 metres with naked
103. All the emission to the air other than steam or water vapour must be odourless and free of mist, fume and
104. A 99.99% destruction and removal efficiency (DRE) for each principal organic hazardous constituent (POHC) in the waste feed where DRE [ ( Win – Wout) /Win ] x

Second Burning Optimum leave temperature level need to be not a lot less than 1100oC

1. The average dioxin and furan concentration in the emission should not exceed 80mg/m3 total dioxins and furans if measured for a period of 6 to 16

• Ease of Use

1. Auto
2. No pilots to
3. Automatic control and temperature monitoring
4. Built-in skid facilitates placement

• Fuel Efficiency

1. Rapid incineration means low fuel

2. Up to 20kgs per hour (dependant on application).
3. Thick refractory lining rated to 1400 deg C in main chamber retains heat, increasing

• Quality Built to Last

1. Heat resistant 3mm
2. Stainless steel

• Key Features

1. Low running and maintenance costs
2. Fully Automatic and simple to operate control panel
3. Afterburner Preheat
4. Incineration Temperatures in Excess of 900 degrees C
5. 3 mm Steel Casing and Fully insulated
6. Dense Refractory Concrete Lining Rated to 1400 degrees C
7. Solid Hearth to Allow Maximum Burnout
8. Large Top Opening Lid For Easy Loading
9. Stainless Steel Flue as standard
10. 12 Months or 1000 hours
11. Optional Stainless Steel Casing
12. Heat Recovery System option

• External Dimensions

• Internal Dimensions

• Operation

1. Minimum Operating Temperature 950
2. Maximum Operating Temperature 1320

• Particulate Removers

SECTION VII

1. Cyclone separator
2. Electrostatic precipitators
3. Fabric filters

• Chimney /Stack

• The chimney should have a minimum height of 10 meters above ground level and clear the highest point of the building by not less than 3 meters for all The topography and height of adjacent buildings within 50 meters radius should be taken into account.
• If possible the chimney should be visible to the operator from the feeding
• The addition of dilution air after combustion in order to achieve the requirement of these guidelines is
• The minimum exit velocity should be 10 m/s and at least twice the surrounding wind speed (Efflux velocity = wind speed x 2) whichever is higher to ensure no down washing of exiting
• Point for the measurement of emissions shall be

• Control Panel

1. Control of 2 burners
2. Timer control 0- 12 hours
3. Integral fan timer control
4. Temperature and thermostatic control

COST TIMETABLE FOR THING

SECTION VII

PRICE SCHEDULE FOR ITEM

Rate schedule for Supply, Installment, Examining as well as Commissioning of an incinerator for Turkwel Power Station