Archive: March 13, 2022

1.The double chamber incinerator shall preferably be designed. Air supply in the primary and secondary chamber shall be regulated between 30%-80% and 170%-120% of stoichiometric amount respectively. Flow meter/suitable flow measurement device shall be provided on the primary and secondary air ducting. The combustion air shall be supplied through a separate forced draft fan accounting for the air supplied through burners. Provision shall be made in the primary chamber to measure the water column pressure.
2. Capacity : up to 4000kg      burn not less than 500 kg /hr
3. medical incinerator manufacturer The refractory lining of the chamber shall be strong enough to sustain minimum temperature of 1000dc in the primary chamber and 1200 dc in the secondary chamber. The refractory& insulation bricks shall have minimum 115mm thickness each & conform to IS:8-1983 & IS:2042-1972 respectively.
4. The incinerator shell shall be made of SS/MS plate of adequate thickness (minimum 5mm) and painted externally with heat resistant aluminium paint suitable to withstand temp.of 250 dc with proper surface preparation. Refractory lining of the hot duct shall be done with refractory castable (minimum 45mm thick)& insulation castable(minimum 80mm thick). Ceramic wool shall be used at hot duct flanges & expansion joints.
5.There shall be a separate burner each for the primary & secondary chamber. The heat input capacity of each burner shall be sufficient to raise the temp.in the primary & secondary chambers as 800+/- 50dc and 1050+/-50dc respectively within maximum of 60 minutes prior to waste charging. The burners shall have automatic switching off/on control to avoid the fluctuations of temperatures beyond the required temp.range.
6.Incinerator shall have graphic or computer recording device which shall automatically and continuously monitor and record dates, time of day, batch sequential number,Co,Co2,O2 in gaseous emission shall also be  measured daily.
7. Structural design of the chimney/stack shall be as per IS:6533-1989.The chimney/stack shall be lined from inside with minimum of 3mm thick natural hard rubber suitable for the duty conditions and shall also conform to IS:4682 part I-1968 to avoid corrosion to oxygen and acids in the flue gas.

8.The incinerator must have an emergency vent. The emergency vent shall remain closed ie. it shall not emit flue gaseous during normal operation of the incinerator.

9.Metal fuel tank from black steel (capacity not less than 2500 litres) and shall be installed at the incinerator Room. The tank shall be provided with all necessary fittings including fill, vent, drain and overflow line, level indication and access for inspection and maintenance. Level switches shall be provided for the following services.

(a) Low level alarm
(b) High level alarm
(c) Low level start of transfer pump
(d) High level stop of transfer pump

10.A ready built fabricated room shall be supplied for housing the incinerator. The room will be designed in such a way that free space is  available  on all sides and heat radiation  kept at minimum and giving the operators an easy workable environment and ventilation. The materials will be sufficient structural thickness of mild steel angles neatly coated with metal primer and epoxy paint to withstand sea corrosion
– effectiveness for the treatment of placenta? and expired or spoiled drugs, cytotoxic and cytostatic drugs prescribed: narcotics eg
– Does it allow to treat drug or waste containing glass (whatever color: transparent or colored white) without causing explosions?
– The ability of the liquid waste treatment (blood, urine stained, other body fluids contaminated, regardless what volume packaging?
– The efficiency of process chemicals (after neutralization and detoxification: solids and liquids)
– Is there  microbiological testing especially: the processing efficiency bascillus

2019-05-18 Новости компании212 просмотров

После долгого подтверждения чертежей и выбора продукта наша компания успешно подписала контракт на поставку медицинской сумки QF в коробке защитного защитного фильтра и извлечении из нее . Объем воздуха составляет 4 000 см / ч, 2200 см / ч и 1500 см / ч соответственно.Материал изготовлен из экономичного холоднокатаного стального листа, окрашенного листовой краской, оснащен американским манометром дифференциального давления Dwyer и инспекционным отверстием DOP. Этот тип входящего и извлекаемого фильтра является стандартным продуктом компании, а также является рентабельным продуктом с разумными инвестициями и значительным эффектом.

   Компания представляет собой хорошо известную отечественную группу фармацевтических предприятий нового типа, объединяющую производство, образование и исследования, науку, промышленность и торговлю. У нее есть две производственные компании, две компании по сбыту и одно лекарство в Ганьчжоу, Пекине, Ханчжоу, Шэньчжэне и Хайкоу. В научно-исследовательском институте и научно-исследовательском институте клинической медицины работает около 2000 сотрудников. Он имеет отечественное и международное первоклассное производственное оборудование и испытательное оборудование, и все рецептуры получили национальную сертификацию GMP.

Nanjing Clover Medical Technology Co.,Ltd.

Tel: +86-13813931455(WhatsApp)

Website: www.hiclover.com

Email: [email protected]

Email: [email protected]

Add: Gangjia Zhihui Industrial Area, Xin Gangwan Rd. Liuhe, Nanjing, China 211500

HICLOVER Solution for Fighting COVID-19, with ISO9001/CE Certification. Auto. Control Waste Incinerator & Auto. Roll Air Filter(Air Purification)

Equipment Access Openings: Organize all piping and equipment to allow access to openings without disassembly of

piping or equipment. Provide space which permits full opening of all doors, panels, and other access openings.

1. Operating Space: Do not reduce or alter personnel working spaces shown except with prior approval of Resident

Engineer.

1. Fuel Oil System: Coordinate set pressure of house fuel oil system with requirements of burner mounted pumps. Do

not exceed blood pressure limits (typically 14 kPa or 2 psi or less), or suction lift capabilities of burner

mounted pumps. Ability of destruction in weight: 60 Kg/h. It should be able to operate not less than 10 hours/day

3. This incinerator has to be able to destruct all combustible wastes produced by hospitals, private clinics,

laboratories, institutes, etc…

4. “PYROLYTIC” combustion, by controlling the gasification of waste.

6. The incinerator must prevent the discharge of smoke and fine dust, during the loadings. It should be able to reduce the quantity of wastes by 98%.

8. It should be able to hold emission in the second burn with gasoline residence of less than 2 seconds.

9. The incineration should be wholly free from visible smoke in addition to offensive odours.

10. The lower calorific power (L.C.P) of this waste will be 3,500 kcal/kg

The Temperatures of combustion: Minimum will be 850oC and max 1400oC

Post combustion: >1100oC.

11. The Internal diameter of the Chimney: Ø 400 and its height: 8 m

12. The Volume of the combustion chamber: 1.200 L

13. The Dimension of the door for loading in cm: 70×70.

14. Burner operation should be Automatic On/Off

15. Fuel: petrol

16. The provider must provide  necessary information for the best of  the installment

This incinerator with”PYROLYTIC” combustion must have:

17. A combustion chamber of waste:

* Perfectly tight doorway for the manual loading of waste. The loading should be Manual, Batch Load

* A reduction of light which the use is restricted to the ignition of waste.

* Frontage of loading with door seals gone up on hinges, wheel of screw plug, flexible joint, and stuffing insulating

out of refractory.

* The insulation of the combustion chamber ought to be composed of refractory bricks, having a

high content of aluminium and insulates bricks to be able to guarantee a minimum temperature on

the outside sheet metal.

* Composition of the refractory;

Refractory concrete :

. Thickness      : ≥100 mm

. Nature: 42 percent of Al203

Insulate in fibrous panels:

. Thickness: ≥75 mm

Nature: Calcium silicate.

* Burner of light of waste, with fuel, standard mono-bloc casting guiding  plunging flame, lighting and safety of

electronic ignition, permanent ventilation, electromagnetic sluice gate of regulation and isolating valve.

* Plate of combustion in Carborundum, avoiding the fixing of glass and slags.

Nature: Calcium silicate.

* Burner of lighting of waste, with fuel, standard mono-bloc casting guiding  plunging flame, lighting and safety of

electronic ignition, permanent ventilation, electromagnetic sluice gate of regulation and isolating valve.

* Plate of combustion in Carborundum, avoiding the fixing of glass and slags.

Pour le camp des Nations Unies (Nations Unies) et de l’UA (Union africaine) à l’aéroport international de Mogadiscio. Nous livrons 02 ensembles d’incinérateur modèle YD-300 et expédions dans un conteneur de 1 × 40 pieds de haut.

L’incinérateur à taux de combustion de 300 kg par heure est très apprécié du marché car ce modèle peut être un équipement d’incinération de déchets médicaux pour les grands hôpitaux et également très bon pour d’autres traitements de déchets solides à moindre coût, même si des animaux de grande taille peuvent également être introduits dans la chambre de combustion. Le volume de la chambre de combustion primaire est de 2,4 m3, assez grand pour les animaux de taille commune. Pour le transport maritime, le YD-300 peut être chargé dans un conteneur de 40 pieds de hauteur.