Archive: May 2, 2021

domestic incinerator

Documents to be submitted as following ;

• Fabricators accreditations
• Test report to prove ZERO harmful emission level provided as samples form other installations
• Test report to prove sterility achieved at 6log to 10 level to be provided upon commissioning report and validation.

Technical proposal include:

• The hospital should provide the necessary space: building & infrastructure, sufficient power steam supply and

connection up to room water & sewage line to the room

• Room preparation: preparation, Renovation & Modification of the room is suppliers responsibility
• The supplier should submit the necessary drawing showing space requirements ( room size (LxWxH) dimensions of

processors & ancillary equipment

• Supplier must give the proposal of the total power requirement of the whole unit and on which the hospital will

ensure the power supply. However connections inside the room is suppliers responsibility

• The connection/fittings form the processor and ancillary equipment to water and sewage line is suppliers

responsibility.

• A detailed training proposal including the duration of staff training on how to operate and maintain the processor
• A detailed maintenance schedule.
• List of spare parts and accessories required for maintenance of the system

Warranty & After Sales Services:

• Warranty period will be minimum 03 years or as offered by the manufacturer which comes later.
• Warranty period will be counted from the date of handing over of machine over of machine to the user in functioning

condition i.e date of commission.

• In warranty period supplier have to provided all maintenance & repair services.
• Breach time will not be counted in warranty period.
• At least 10 years back up service (including warranty period) has to be ensured by the supplier.
• The repair/maintenance work should be carried out within 72 hours after getting request for such from the user.

Quality standard: CE/FDA certificate of the offered item must be submitted with the offer.

• For verification of the certificate bidder must submit the following :

1. i) Mailing address of the issuer of the certificate.
2. ii) Website, Email address & Fax & Telephone Number of the issuer.

• The bid will be non-responsive if:

1. i) The certificate issuer can not be reached
2. ii) The issuer fails to authentic the certificate within the bid validity

iii)   The issuer confirms that the submitted certificate is defective in terms of authenticity or validity.

TECHNICAL INCINERATORS SPECIFICATIONS FOR 2 hospitals in Kenya

TECHNICAL INCINERATORS SPECIFICATIONS FOR 2 hospitals

INTRODUCTION

• All the incinerators to be supplied and installed must meet the Government of Kenya waste Management Regulation 2006 in particular 3^rdschedule regulation (26, 47) pertaining classification, standards, criteria, and procedure for installing/operating incinerators as authored by the National Environmental Management and Coordination (waste management) regulation 2006, legal notice No. 121 of 29^th September 2006
• The capacity of the incinerator required should be to the specifications with a capacity to burn 100kgs/Hr
• The incinerator shall be run on a 3-phase power supply (mains)
• For the technical evaluation, not only the treatment plant but the entire system will be considered.  It will be the responsibility of the Bidder to supply a full system, including all eventually additionally necessary secondary systems and additional equipment.
• The system offered shall be designed to operate normally under the conditions of the purchaser’s country. The conditions include Power Supply, Climate, Temperature, Humidity, etc.
• The Bidder must provide a warranty for one year.
• All text, parameter etc. on all control operating interfaces as well as on information displays and on print-outs shall be in English language.
• The Bidder is responsible for all permits and approvals for importation. The Bidder shall provide all the necessary documentation in order to facilitate the legal requirements for the installation and putting into use of the equipment.
• Period of Execution is 90 days from contract signature for delivery to site and completion of all verification operations required for the issuance of provisional acceptance.
• Representatives of the Contracting Authority and the Beneficiary, together with the Bidder’s representative, shall carry out the controls, testing and initial approval for provisional and final acceptance as.  The provisional and final acceptance shall take place at the final destination.
• After-Sales Service: The Bidder is required to ensure that a maintenance, service and repair centre, which is authorised by the Manufacturer, and which is able to rapidly supply genuine spare parts and consumables recommended by the Manufacturer is available throughout the one year warranty period. In fulfillment of this requirement with their offer Bidders must submit a statement signed by a representative of the manufacturer:
  • Providing the name and address of its authorised maintenance, service and repair centre,
  • Confirming that this authorised maintenance, service and repair centre is able to rapidly supply genuine spare parts and the consumables recommended by the Manufacturer; and

• The Bidder will be responsible to deliver and install all to be supplied equipment at to be set up waste handling areas in the Republic of Kenya. The Bidder shall deliver a time schedule over the complete construction and assembling period. The delivery and installation time must be agreed between bidders, target Hospital and the Contracting Authority. The treatment plant must arrive pre-assembled. The Bidder shall ensure that all parts of the plant transported by sea shall not be shipped as “deck cargo”.

• It is expected that the Bidder cooperates closely with the contractor for the new waste handling building/area and will make available all needed technical information, drawing, etc. to the contractor.

• The Bidder shall supply and install the incinerator with the following attached specifications

EVALUATION CRITERIA

Evaluation shall be carried out in four stages namely preliminary examination of documents for conformance with mandatory requirements, technical evaluation, site visit and commercial evaluation.

Stage One: Preliminary Examination

– Preliminary Evaluation under special condition of the tender. These are mandatory requirements.

This shall include confirmation that a bidder has complied with the special condition of tender above.

Failure to meet any one of the above requirements stated in the special conditions of the contract shall lead to automatic disqualification.

Stage Two: TECHNICAL EVALUATION (70 MARKS)

Pass mark for technical evaluation is 70/100 marks

Stage Three: Site Visit

The evaluation committee will visit the premises of the bidders who are responsive to technical  evaluation stage to verify the authenticity of statutory document submitted; ascertain the accuracy of the information given in the tender documents, assess firm’s capacity, location, among others.

The Tenderer will be automatically disqualified where false or fraudulent Information is found to have been given.

Stage 4 Commercial Evaluation

Bids that pass the above three (3) stages shall be compared on the basis of prices / cost quoted and the lowest priced will be considered the lowest evaluated bid and subsequently recommended for award. Prevailing market prices will be used to determine the price responsiveness of the bidders.

SECTION V – SCHEDULE OF REQUIREMENTS

Signature of tenderer

Note: In case of discrepancy between unit price and total, the unit price shall prevail.

SECTION VI – STANDARD FORMS

1. Form of tender
2. Contract form
3. Confidential Questionnaire form
4. Tender security form
5. Performance security form
6. Bank guarantee for advance payment
7. Declaration form

smart ash incinerator

(G) Technical Specifications of Spore tester Features and Specifications :

• It is an auto reader for Bacillus Stearothermophilus to test the spore discharge after treatment (sterilization) of

the waste.

• should be a very Accurate, reliable and easy-to-use units for reading rapid readout biological indicators (RRBI) for

steam sterilizer

• Automatically reads indicator results.
• There should be red plus (+) light to indicate sterilization failure and a green negative (-) light to confirm that

the sterilization conditions have been met.

• Audible alarm in case of positive result detected and RRBI is removed from the reader before final results have been

detected.

• There should also be a Buzzen alarm OFF button.
• The unit should be maintenance-free equipment and there should not be any light bulbs to replace for maintenance.
• At least 12 Incubation/reader wells
• A crushing well
• Digital display
• A press-button by pressing which the incubation time remaining for each individual incubation/reader well that

contains a RRBI will be displayed.

• Power: 220 VAC, 50Hz

Accessories to be included;

• Samples/kits-100 pcs

3 Chamber Incinerator

Primary chamber:
Heavy duty mild steel casing, High quality Refractory lining and insulation 01 x natural gas ignition burners (automatic)  01 x temperature sensor points with complete internal fans.
Secondary Chamber:
Heavy duty mild steel casing, high quality refractory lining and insulation 01 x natural gas burners (automatic) with complete 01 internal fans. 02 Sec gas residence times.
Third Chamber:
Heavy duty mild steel casing, high quality refractory lining and insulation 01 x natural gas ignition burners (automatic) with complete internal fans. 02 Sec gas residence time.
Integrated dual flu gas washer:

Resultant gasses passed through dual gas filtration system for maximum clean emission. It is also equipped with chain filters.
Chimney:
Heavy duty 5mm or more stainless steel casing mild steel casing.
Stack cap/spark arrestors.
Control Panel:
a.Temperature Monitoring with 4 digit display.
b.Thermostat control device for burner (fuel saver)
c.Temperature control 0-12 hours.
d.Integral fan timer control

incinerator manufacturers

3 Chamber Incinerator

Primary chamber:
Heavy duty mild steel casing, High quality Refractory lining and insulation 01 x natural gas ignition burners (automatic)  01 x temperature sensor points with complete internal fans.
Secondary Chamber:
Heavy duty mild steel casing, high quality refractory lining and insulation 01 x natural gas burners (automatic) with complete 01 internal fans. 02 Sec gas residence times.
Third Chamber:
Heavy duty mild steel casing, high quality refractory lining and insulation 01 x natural gas ignition burners (automatic) with complete internal fans. 02 Sec gas residence time.
Integrated dual flu gas washer:

Resultant gasses passed through dual gas filtration system for maximum clean emission. It is also equipped with chain filters.
Chimney:
Heavy duty 5mm or more stainless steel casing mild steel casing.
Stack cap/spark arrestors.
Control Panel:
a.Temperature Monitoring with 4 digit display.
b.Thermostat control device for burner (fuel saver)
c.Temperature control 0-12 hours.
d.Integral fan timer control