Archive: April 24, 2021

Air Emissions Environmental Specifications CA

Air emission requirements establish limits on the quantity of contaminants that can be launched into the ambience. These standards are revealed as a focus in the exhaust gases leaving the stack as well as can being accomplished making use of usually available incineration innovation and waste diversion methods. The complying with emission standards1 relate to existing, new or broadening solid waste incinerators running in Nunavut and have been taken on from the Canadian Council of Ministers of the Environment (CCME) Canada-Wide Criteria for Dioxins as well as Furans and Mercury Emissions, specifically. Comparable criteria for the open burning of solid waste have not been developed.

Table 1. Air Emission Requirements for Solid Waste Incinerators

Specification Numeric Standard Description

Dioxins and Furans
80 pg I-TEQ/cubic metre
Device of procedure is picograms of International Toxicity
Matchings per cubic metre of air

Mercury
20 µg/ Rcubic metre
System of procedure is micrograms per Referral cubic metre (the quantity of gas adapted to 25oC and also 101.3 kilopascals)

Opacity is the level to which the exhaust gases decrease the transmission of light and obscure the sight of any type of object in the background. It is expressed as a portion representing the degree to which a things watched with the gases is covered. Although not an emission standard, opacity gives a sign of the general efficiency of the burner during normal operation2. Opacity in the incinerator stack need to not go beyond 5%. While it is not prepared for that opacity degrees would exceed 1% to 2% under regular operation, values higher than 5% suggest the burner is not executing appropriately as well as added efficiency examination as well as modification is called for.

Figure 6 – – Examples of Smoke Opacity Scores
The opacity rankings are estimates as well as are provided for illustrative objectives only
Centre and also best photos thanks to GNWT Department of Atmosphere as well as Natural Resources

Regarding Hiclover Medical Enviromental

HICLOVER, Nanjing Clover Medical Innovation Co., Ltd, supply system options for medical environmental management, animal and also family pet cremation engineering, other metropolitan strong waste incineration task.
We provide single combustion chamber, double burning chambers, 3 burning chambers and also multi-combustion chambers waste incinerators for laboratory, center, health center, medical center, hygiene medical waste devastation with medical non reusable, biological waste, clinical plastic waste, hazardous waste, red bag waste, needle disposal, gauze as well as bandages, sealed sharp containers, pathological waste, trace-chemotherapeutic wastes, etc
.
Our series of incinerators cater for little to big scale pet cremation related services, such as chicken ranches, cattle farms, lamb farms, pig farms, stables, kennels, screening research laboratory, catteries, pet dog crematoriums.

The burner shed waste in primary burning chamber and also burn the smoke from key combustion chamber once more to make sure environmentally friendly with no black smoke, smelless, lower pathogenic microorganisms infection.
System solutions for medical waste ecological, including waste incineration, smoke emission therapy, high-temperature sanitation, ultraviolet sanitation lamp, waste shredder, needle destroyer, clinical waste plan, sharp containers, etc.

The family pet cremation equipment humanized design with movable platform, little area covers for modern-day pet dog cremation local business owner all over the world.
The containerized mobile incinerator mounted in ISO container prior to leave manufacturing facility, pre-installation, no incineration home develop building and construction, movable by truck and also ultraviolet light sanitation inside.
HICLOVER is growing brand for environmental protection field, and also market show most of Africa, Middle East, Southeast Asia countries as well as component of North America, Europe area. We a re relied on companion for governmental organizations, charitable organizations, international contractors, logistics organizations, military, pet cremation entrepreneur, etc. We have export experience greater than 40 countries, including war zone like Iraq, Afghanistan, Somalia, South Sudan.

We are china incinerator manufacturer, specialist and also merchant. Manufacturer make reasonable rate for incinerator customer, supply medical burner, health center incinerator, animal burners, hog burners, family pet cremation tools, little incinerator, family pet incinerator, animal burner, mobile incinerator, tiny animal burner, transmittable waste pyrolysis machine, research laboratory incinerator. HICLOVER aid client minimize acquisition spending plan, custom made feature, quality items and also pleasant solution.

clinical was incinerators Department of Wellness

health center waste administration group at a tertiary care health center,1250 beeded hsopital.
our everyday waste created from all resources is 0.55 kg/bed/day =685kg/day
we need an incinerator of 150kg/hour filling capability.
plz reply with, buying, installment, running as well as upkeep cost.incinerators, especially, medical was burners
Department of Health has actually floated a tender for Burner X 1 Device and also the closing day is on 16th June 2011. The spec of the Burner is as listed below:
Requirements of Burner
1. Must have preparation, Incineration, Scrubber steps to melt waste entirely and also waste gas need to be non-polluted
2. Strong steel, heat immune coating, stainless steel cover, painted tubular steel framework, 2-blowers, axial vane, appropriate drum (S/S, thick) for the burner should be provided.
3. Approximate. 20 to 25 Kg per set and the time needed for 1 set not more than 1 hour usually.
4. Ash should be only 5% of the waste material
5. Weight of Incinerator– 50-60 Kg
6. 220V Air Conditioning
7. Surgical, clinical & & laboratory waste
8. B X L X H = 4 feet X 8 feet X 6 feet
9. 1 year service warranty
10. ISO Licensed
11. Mobile Burner
12. Electric

Needed Specs for Mobile Incinerator

Functional Capacities

• PROCESS MINIMUM 1 TON PER DAY
• OPERATED WITH LIMITED TRAINING
• REGULAR MAINTENANCE CAN BE COMPLETED WITH LIMITED TRAINING
• COMPLIES WITH EURO / OR US-EPA EMISSION STANDARDS
• ABILITY TO BURN WASTE LUBRICANTS (POL)
• HANDLE ORGANIC SOLIDS (TO INCLUDE RMW)
• DEPLOYABLE
• MOBILE
• 24 HRS OF CONTINUOUS USE
• AUTOMATIC LOADING SYSTEM
• AUTOMATED ASH REMOVAL SYSTEM
• GAS SCRUBBING SYSTEM
• 95% REDUCTION OF SOLID WASTE
• OPERATE OFF DIESEL OR FUEL OIL
• CAPABLE OF BURNING 4 UNITS OF WASTE PER UNIT OF FUEL
• ABLE TO TAKE ALL COMBUSTIBLE WASTE TO INCLUDE: PAPER, PLASTIC, CARDBOARD, FOOD, USED OILS, SLUDGE, OILY RAGS, WOOD
• NO PRE-TREATMENT OF WASTE REQUIRED
• FIVE (5) YEAR COMPONENT WARRANTY

Technical Specifications

• OPERATION MANUAL AND TRAINING MANUAL FOR EACH INCINERATOR
• SET UP AND INSTALLATION INSTRUCTION MANUALS
• BLUE PRINT/ SCHEMATIC PROVIDED THAT OUTLINES THE PHYSICAL DIMENSIONS OF THE 20’ INCINERATORS
• INCINERATORS COMPOSED WITH HEAVY DUTY WELDED CONSTRUCTION
• OPERATED AND TRANSPORTED IN 20’ INCINERATORS (CONTAINERS)
• FULL FRONT AND OPTIONAL REAR ACCESS
• PRIMARY / SECONDARY TEMPERATURE CONTROLS

medical facility incinerator manufacturers

SECTION V

• TECHNICAL SPECIFICATIONS OF THE INCINERATOR

• General Description

The plant have to have four distinct sections that show three principles of disturbance, home time and temperature retention. The regulated areas may consist of but not limited to:

1. Overall plant layout
2. Feed chamber/charging
3. Primary combustion chamber
4. Particulate scrubbers
5. Acid gas
6. The stack/chimney.
7. Minimum capacity of primary chamber = 10cubic meters
8. Burn rate (rate of waste incineration) = 10 kg per hour
9. Should have a full width counterbalance loading door allowing easy access to the main chamber for loading and removing ash.
10. The INCINERATOR should be NEMA approved in accordance with Environmental management and coordination (Waste management) Regulations of 2006.

• Scope Of Work

The job specified in the agreement will consist of.

1. Supply, install and commission an incinerator as provided   in the technical specifications

2. Provision for adherence to OSHA and other statutory requirement relating to Health and Safety of workers during execution of the works covered in this

3. Assessment and preparation  and construction of  a standard incinerator shed with one waste  storage room  ( see the design )

4. Provision of operation and maintenance manuals and drawings complete with maintenance schedule and

5. Fuel oil storage tank- Mild steel 1000 liters capacity

6. Onsite training for operation and maintenance

IMPORTANT

To enable the Company carry out definitive analysis of the tender, tenderers are asked for to submit with their offers the comprehensive requirements, drawings and catalogues with Appointing and maintenance directions for the Incinerator they intend to Supply, mount and also commission.

Tenderers that stop working to comply with this need totally shall have their tender declined.

3. TECHICAL SPECIFICATIONS OF THE INCINERATOR

3.1 Feeding as well as Charging

Controlled sanitary mechanical feeding that does not negatively influence the air temperature in the primary as well as additional chambers of the incinerator will be made use of.

• Primary Combustion

• This chamber should be equipped with burners that use low sulphur
• The chamber should ensure a minimum exit temperature of 850 degrees
• This unit should operate at over 1100 deg C to ensure complete
• This chamber should be equipped with burners that use low sulphur
• Heavy-duty steel casing
• High quality refractory lining and insulation
• Large full size top load door and liquid retention
• 1 x oil fired ignition burners operated on/off

• Secondary Combustion Chamber (After burner)

1. Heavy-duty steel casing
2. High quality refractory lining and insulation
3. 1 x oil burner
4. Should be fitted with burners that use low sulphur
5. Ensure secondary air supply is controlled.
6. Ensure residence time is not less than two seconds.
7. Ensure that the gas temperature as measured against the inside wall in the secondary chamber and not in the flame zone is not less than 1100 degrees
8. Ensure the emitted oxygen content of the emitted gases is not less than 11%
9. Ensure both primary and secondary combustion temperatures are maintained until all waste is completely

• Particulate Removers

A mechanical particulate collector should be incorporated after secondary burning chamber for elimination of particulate contaminants entrained in the flue gas stream. The particle enthusiasts may include any of the following or a combination thereof:

1. Cyclone separator
2. Electrostatic precipitators
3. Fabric filters

• Chimney/Stack

1. The chimney should have a minimum height of 10 meters above ground level and clear the highest point of the building by not less than 3 meters for all The topography and height of adjacent buildings within 50 meters radius should be taken into account.
2. The chimney should be visible to the operator from the feeding

1. The minimum exit velocity should be 10 meters per second and at least twice the surrounding wind speed (Efflux velocity = wind speed x 2) whichever is higher to ensure no down washing of exiting
2. The point for measurement of emissions shall be

• Instrumentation

1. Instrument for determining the inside wall temperature and not burner flame temperature must be provided for both primary and secondary
2. An audible and visible alarm must be installed to warn the operator when the secondary chamber temperature drops to below the required
3. A carbon monoxide and oxygen meter/recorder should be
4. A smoke density meter/recorder should be
5. A solid particulate meter/recorder should be
6. Any other instrument that may be considered

• Location / Siting of the Incinerator

1. a) The incinerator must be sited in accordance with the relevant local municipal authority planning regulations and the topography of the site must be compatible with premises in the

• Emission Limits

99. Combustion efficiency (C.E) shall be at least00% where C.E = %Carbon dioxide x 100 / [% Carbon dioxide + carbon monoxide]
100. The temperature of the primary chamber shall be 800 +/- 50 degrees centigrade
101. The secondary chamber gas residence time shall be at least 1 second at 1050 +/- 50 degrees centigrade with 3% oxygen in the stack
102. Opacity of the smoke must not exceed 20% viewed from 50 metres with naked
103. All the emission to the air other than steam or water vapour must be odourless and free of mist, fume and
104. A 99.99% destruction and removal efficiency (DRE) for each principal organic hazardous constituent (POHC) in the waste feed where DRE [ ( Win – Wout) /Win ] x

100 where Victory = mass feed price of the POHC in the waste stream fed to burner as well as Wout = mass emission rate of POHC in the stack prior to the release to the ambience.

1. The average dioxin and furan concentration in the emission should not exceed 80mg/m3 total dioxins and furans if measured for a period of 6 to 16

• Ease of Use

1. Auto
2. No pilots to
3. Automatic control and temperature monitoring
4. Built-in skid facilitates placement

• Fuel Efficiency

1. Rapid incineration means low fuel

2. Up to 20kgs per hour (dependant on application).
3. Thick refractory lining rated to 1400 deg C in main chamber retains heat, increasing

• Quality Built to Last

1. Heat resistant 3mm
2. Stainless steel

• Key Features

1. Low running and maintenance costs
2. Fully Automatic and simple to operate control panel
3. Afterburner Preheat
4. Incineration Temperatures in Excess of 900 degrees C
5. 3 mm Steel Casing and Fully insulated
6. Dense Refractory Concrete Lining Rated to 1400 degrees C
7. Solid Hearth to Allow Maximum Burnout
8. Large Top Opening Lid For Easy Loading
9. Stainless Steel Flue as standard
10. 12 Months or 1000 hours
11. Optional Stainless Steel Casing
12. Heat Recovery System option

• External Dimensions

• Internal Dimensions

• Operation

1. Minimum Operating Temperature 950
2. Maximum Operating Temperature 1320

• Particulate Removers

A mechanical particle collection agency should be incorporated after additional burning chamber for elimination of particle contaminants entrained in the flue gas stream. The particle collectors may consist of any of the complying with or a mix thereof:

1. Cyclone separator
2. Electrostatic precipitators
3. Fabric filters

• Chimney /Stack

• The chimney should have a minimum height of 10 meters above ground level and clear the highest point of the building by not less than 3 meters for all The topography and height of adjacent buildings within 50 meters radius should be taken into account.
• If possible the chimney should be visible to the operator from the feeding
• The addition of dilution air after combustion in order to achieve the requirement of these guidelines is
• The minimum exit velocity should be 10 m/s and at least twice the surrounding wind speed (Efflux velocity = wind speed x 2) whichever is higher to ensure no down washing of exiting
• Point for the measurement of emissions shall be

• Control Panel

1. Control of 2 burners
2. Timer control 0- 12 hours
3. Integral fan timer control
4. Temperature and thermostatic control

TIMETABLE 2

SECTION VII

PRICE SCHEDULE FOR ITEM

Rate schedule for Supply, Installment, Examining as well as Commissioning of an incinerator for Turkwel Power Station

hospital incinerator supplier

Up to 600kgs per ten-hour day of Kind IV pathological waste or red bag waste rated at 2200 BTU’s per kg, based on batch

packing twice daily.
Burner, 20 kg/hr Burn Ability (min. 1200 kgs. Waste Feed Ability each day) (4-6 hrs procedures) (Power Supply

380V, 50Hz, 3Ph).
Capacity: 30 kg/hr.

Number product: 01 system

Can you please send us cataloge information for Pet Cremation of dogs, pet cats.

– – Please services call for: General concerning Cremation system which is suitable.
for your items, technical transfer and also training for operators.
Containerized Incinerators Operational Capabilities – PROCEDURE 1+ TONS/ DAY – RAN WITH LIMITED TRAINING – REGULAR

MAINTENANCE CONTAINER BE FINISHED WITH RESTRICTED TRAINING – COMPLIES WITH EURO/ OR US-EPA DISCHARGE REQUIREMENTS – CAPABILITY TO MELT

SQUANDERED LUBRICANTS (POL) – HANDLE ORGANIC SOLIDS (TO CONSIST OF RMW) – DEPLOYABLE – MOBILE – 24 HUMANS RESOURCES OF CONTINUOUS USE –

AUTOMATIC LOADING SYSTEM – AUTOMATED ASH REMOVAL SYSTEM – GAS SCRUBBING SYSTEM – 95% DECREASE OF SOLID WASTE – RUN

OFF DIESEL OR FUEL OIL – EFFICIENT IN BURNING 4 DEVICES OF WASTE EACH OF GAS – ABLE TO TAKE ALL COMBUSTIBLE WASTE TO

INCLUDE: PAPER, PLASTIC, CARDBOARD, FOOD, USED OILS, SLUDGE, OILY RAGS, TIMBER PALLETS. – NO PRE-TREATMENT OF WASTE

REQUIRED – VENDOR REPAIR WORK OFFERED AT FACTOR OF SHIPMENT – 5 (5) YEAR ELEMENT SERVICE WARRANTY FROM DATE OF ACCEPTANCE

Technical Requirements – PROCEDURE GUIDEBOOK As Well As TRAINING MANUAL FOR EACH INCINERATOR – ESTABLISH As Well As SETUP

USER’S MANUAL – BLUE PRINT/ SCHEMATIC OFFERED THAT DETAILS THE PHY SICAL CAPACITIES OF THE 20′ INCINERATORS –

INCINERATORS MADE UP WITH HEAVY DUTY BONDED BUILDING – OPERATED AND ALSO CARRIED IN 20′ INCINERATORS (CONTAINERS) –

FULL FRONT As Well As OPTIONAL REAR GAIN ACCESS TO – PRIMARY/ SECONDARY TEMPERATURE MANAGES – COMBUSTION AIR DAMPER – VAPOR LIMITED

LIGHT FIXTURES & & 120V ELECTRICAL OUTLET – OUTDOOR PLU-IN RECEPTABLE FOR ELECTRICAL RESOURCE – OUTDOOR FUEL TRAIN WITH SHUT-OFF – LOAD

RAMP – SKID– PLACED GAS TANK – ELECTRICAL AND GAS OIL CONNECTORS – CONTROL PANEL As Well As AIR LOUVER – AIR MANIFOLD

ACCESS As Well As ENERGY BULKHEAD – GALVANIZED DELIVERY COVERS – GAS, WATER As Well As OIL ADAPTER LINES – PRIMARY AND SECONDARY

BURNERS – FULLY INTEGRATED PLC CONTROL SYSTEM – FACTORY EXAMINED, WIRED PRIOR TO DELIVERY – FLEXIBILITY: NO HEAVY LIFT

DEVICES NEEDED FOR SET UP OR TAKE DOWN – HEIGHT RESTRICTED TO THE HIGHEST POINT ON BASE OR UNDER 15FT HIGH

lab incinerator china manufacturer

Incinerator double chamber with ability 1.5 m3/batch or 6 m3/ day, electronic thermocontrol range 0‐1200

C, thermocouple, air supply capacity 10m3/ minute, power usage 1.2 kWH/ hour, power 3

stage with netral, cooling water sprinkler capacity 5L/ minute, finished with refractory (insulation,

castable, ceramic covering) and PLC

SUPPLY, INSTALLATION As Well As COMMISSIONING OF WASTE BURNER– TECHNICAL SPECS

The Waste Incinerator is created to burn Type IV of pathological waste as well as contagious, infected “red bag,” surgical

dressings, plastic examination devices and also various other wastes.
General Specs
Burner: 2 heaters (primary heater as well as second heater).
Fuel: Oil.
Capacity (Cubic Mtr): 0.65.
Ave Capacity: 60 kg per hour.
Gas Intake (ltrs/ hr):13.
Outside Dimensions.
Size (mm): 2300.
Size (mm): 1220.
Elevation Incl. Flue (mm) 7000.
Door Opening (mm) 610 x 710 610 x 710.
Operation.
Minutes. Operating Temperature level: 950.
Max. Operating Temperature: 1320.
Residency Time in Second Chamber: 5 sec.
Temperature Level Monitoring: YES.
Various other information.
Easy and safe operation.
Huge counter-balanced fill door with electrical lockout.
Automatic control system gives preset melt times and shut down.
Reload light indicates to driver when it is time to reenergize.
Be required for exhaustion of last charge.
Low power usage degrees.
Programmable electronic temperature controls preserve temperature level, assuring complete combustion while conserving fuel.
Stress blower with regulating air control creates disturbance as well as disperses burning air to additional chamber.
Second heater with temperature triggered modulating control offers fast preheat and sustains high temperature

efficiency at low power usage degrees.
Charging price

incinerator sort of pyrolytic medical waste incinerator ability

Including:Incinerator: Structure to be specified
The mark to be specified
Water temperature: 800 to 1000 ° C;
Refractory
Temperature of more than 1100 ° C + obtained;
Capacity: 20-50 kg / hour
Fireplace: 4 to 6 meters high;
Dimension 70 cmx70 crn
Height: 1.10 meters
Fuel: coal;
Aspiration: natural

– A receiving cage for biomedical waste;

– A combustion chamber with a chimney with a filter to retain the ashes;

Chimney section: about 300 cm; With a minimum height of 6 m

Door size: approximately 50×60 cm

Supplied with a 500 liters fuel tank and all necessary accessories for installation.
–                          INCINERATOR for pharmaceutical waste treatment with                  a scrubbing system

With the following technical data:

1.      One pharma solid waste incinerator unit containing two combustion chambers and based on steel base with scrubbing

system.

2.      Working hour /day: minimum 10 hours/day.

3.      Capacity: Approximated 150 kg/hr. Over 10 hrs.

4.      Wastes characteristics:

·         BULK density: 70 – 100 kg/ bm³.

·         Calorific value: 2000-3000 kcal / hr.

·         Moisture content: 20-30%by weight.

·         Ash content: 2 – 8 % by weight.

·         Plastic content: 15-20 % by weight.

5.      Two combustion chambers.

6.      Operating temperatures:

·         First chamber: not less than 700 – 800 °c.

·         Second chamber: not less than 1200 °c (during steady operation).

7.      The burners should be automatically switched off if any of the combustion chambers doors is open.

8.      The burners of the first and second combustion chambers are selected for burning diesel oil (light fuel).

9.      Automatic loader and unloader to be provided.

10.     Exhaust gases to be comply with International Environmental code and requirements.

diesel oil fired medical waste incenerator

Heat Waste Incinerator Design D. MEGABYTES 750XL Melt Rate-150Kg/ hr minimum Weight( Kg) -4000 kg Additional Chamber

(dual chamber with post-burning) Gas Retention Time 2 2nd Gas Diesel Power Supply for control box 220V-240, single

phase 50-60Hz Minimum operating temperature level 1200 oC One year spare parts bundle for complete maintainability 10m pipe

pipeline. 1100 litre fuel Storage tank +pipeline system Containerised (the container will certainly act as housing) Added chimney expansion

1 metre high One (1) year guarantee.

Burner of 20 Kg: 03 Devices

Electrically controlled burner.

Two-compartment burner with an ability of 20 kg/ hour.

Incinerator with reduced upkeep and operating costs; Geared up with an automatic control panel as well as very easy to make use of with

electro-magnetic locking of the door.

A main waste decrease chamber of 900 ° C. A blog post second burning chamber of gases created in the main chamber

at the very least 1100 ° C.

Carbon residues in ash much less than 5% by weight in accordance with European Directive 2000/76/ EC.

With refractory cellular lining in products of higher quality
1/ Cost of a 200kgs/Hr medical waste burner.
2/ (CIF Term) Price of delivery from manufacturing facility to PAPUA NEW GUINEA port of LAE, Morobe province
3/ Price of 2 Clover engineers to Supervise, Installation, Training our engineers and appointing the medical; waste

incinerator.

maker of ha zardous waste burner in china

Burning Capability: 125 kg minimum/time (3-6times/ day), dual chamber, dual combustion system
Imputing door Mouth Width (mm): 760 * 760 (approx.).
Smokeshaft External Size (mm): 300 ± 10.
Combustion Improver Device: 0.11 kw, Fuel intake: 7kg/ hr (max).
Re-Burning Tool: Oil consumption: 5kg/h, 0.37 kw, Oil consumption: 10-20kg/ h.
Voltage: 380v/220v Air Conditioner, Service Warranty: 1 Year, 50 Hz

Per your advertisement for 300 kg.hr. Version– We need to know the rate through return.

The amount of Kg. of Gas would be required for running this Design 10 hrs. day-to-day.

We have our own Freight Forwarding Agent.

We had a Contract for Rubbish Monitoring prior to their Civil Battle for 120 Tons/Day for one Town in North Africa.
Medical Waste Burner

Twin Chamber (Main & & Secondary) with insulation pieces (completely insulated inner refractory lining) in addition to

regulated air blower for each chamber

Insulation/ Refractory Thickness: ≥ 100mm

Chamber plate thickness: ≥ 6mm

Fuel Kind: Natural gas based on shedding fuel in combustion chambers

Waste Ability: ≈ 150 Kg/Day

Incineration capacity: ≈ 25 Kg/Day (Different waste billing as well as waste elimination doors)

Burners: At the very least with (02) burners of automated begin and quit functions

Combustion efficiency: > > 97%

Temperature: programmable temperature with temp monitoring system

Residence time: 2 2nd in secondary chamber

Heating value: 4000 Kcal

Temperature Level Variety: ≈ min 800ºC to max 1200ºC

Electrical supply: 220V with solitary stage

Smokeshaft Plate Thickness: ≥ 5mm

Water scrubber: Rubbing making use of reagent like lime & & must made of SS 10 gauge of non-corrosion properties and painted

exteriorly by tools grade heat repellent enamel

Chimney Height: in between 15-25 feet